Differences

This shows you the differences between two versions of the page.

--- en:configuration_api [2018/12/28 12:51]
kkshin [BS2CardConfig]
+++ en:configuration_api [2020/02/18 10:00]
yjjung [Configuration API]
@@ Line 57: / Line 57: @@
   * [[BS2_GetCardConfigEx]]: Retrieves iClass SEOS card settings from the device.
   * [[BS2_SetCardConfigEx]]: Stores iClass SEOS card settings on the device.
-  * [[BS2_GetDstConfig]]: Gets the device DST information.
+  * [[BS2_GetDstConfig]]: Retrieves the device DST information.
-  * [[BS2_SetDstConfig]]: Sets the device DST information.
+  * [[BS2_SetDstConfig]]: Stores the device DST information.
+  * [[BS2_GetSupportedConfigMask]]: Retrieves supported configuration of the device.
+  * [[BS2_GetIPConfigViaUDPEx]]: [+ 2.6.3] Retrieves IP configuration through UDP broadcast with host IP.
+  * [[BS2_SetIPConfigViaUDPEx]]: [+ 2.6.3] Stores IP configuration through UDP broadcast with host IP.
+  * [[BS2_GetIPV6Config]]: [+ 2.6.3] Retrieves IPv6 configuration information.
+  * [[BS2_SetIPV6Config]]: [+ 2.6.3] Stores IPv6 configuration information.
+  * [[BS2_GetIPV6ConfigViaUDP]]: [+ 2.6.3] Retrieves IPv6 configuration through UDP broadcast.
+  * [[BS2_SetIPV6ConfigViaUDP]]: [+ 2.6.3] Stores IPv6 configuration through UDP broadcast.
+  * [[BS2_GetIPV6ConfigViaUDPEx]]: [+ 2.6.3] Retrieves IPv6 configuration through UDP broadcast with host IP.
+  * [[BS2_SetIPV6ConfigViaUDPEx]]: [+ 2.6.3] Stores IPv6 configuration through UDP broadcast with host IP.
 \\
 ===== Structure =====
@@ Line 127: / Line 136: @@
     uint32_t cameraFrequency;
     bool secureTamper;
-private:
+    bool reserved0;     // (write protected)
-    bool tamperOn;     // (write protected)
+    uint8_t reserved[2];
-    uint8_t reserved[2];
     uint8_t reserved2[20];
 } BS2SystemConfig;
@@ Line 146: / Line 154: @@
 Decides whether to use intercom. \\ \\
 **7. //useUSBConnection//** \\
-Decides whether to use USB connection. \\ \\
+This is not used anymore. (The device automatically detects USB connection.) \\ \\
 **8. //keyEncrypted//** \\
 Decides whether to use OSDP secure key. \\ \\
@@ Line 164: / Line 172: @@
 Flag to determine whether to use a security tamper. \\
 When Tamper on, the following data is deleted from the device. (User, log, data encryption key, SSL certificate) \\ \\
-**13. //tamperOn//** \\
+**13. //reserved0//** \\
-The information to manage the tampering internally, which should not be set. \\
+Reserved space. \\ \\
-Be sure to call [[BS2_SetSystemConfig]] after completing the necessary settings except for tamperOn after [[BS2_GetSystemConfig]]. \\ \\
+**14. //reserved//** \\
-**14. //reserved1//** \\
 Reserved space. \\ \\
 **15. //reserved2//** \\
@@ Line 201: / Line 208: @@
 If the value in the array is greater than 0, the corresponding authentication mode is enabled. \\
 Biometric information in the descriptions below refers to the fingerprint or face depending on the device. \\
-<WRAP group 50%>
+<WRAP group 60%>
 ^Value ^Code  ^Description  ^
 |0  |BS2_AUTH_MODE_BIOMETRIC_ONLY  |Biometric only |
@@ Line 233: / Line 240: @@
 **7. //faceDetectionLevel//** \\
 Level of face detection in user authentication. If the detected face level is lower than the configuration, it will be processed as authentication fail.\\
+When set, the camera view according to Normal/Strict is displayed, access is denied if the device doesn't recognize facial image through image log. Default is 0.
 <WRAP group 50%>
 ^Value  ^Description  ^
@@ Line 240: / Line 248: @@
 </WRAP>
 <WRAP info>
-Only valid for devices with a camera.
+Only valid for A2. Not used with FaceStation2 or FaceLite.
 </WRAP>
 **8. //useServerMatching//** \\
@@ Line 572: / Line 580: @@
     uint8_t fileID;
     uint8_t encryptionType;
-    uint8_t reserved[3];
+    uint8_t operationMode;
+    uint8_t reserved[2];
 } BS2DesFireCard;
@@ Line 618: / Line 627: @@
 File ID that is stored inside the DesFire card, which will be used by the application to read and write data.\\ \\
 **15. //encryptionType//** \\
-Type of data encryption. AES will be supported soon.\\
+Type of data encryption.\\
 <WRAP group 50%>
 ^Value  ^Description  ^
@@ Line 624: / Line 633: @@
 |1  |AES  |
 </WRAP>
-**16. //reserved//** \\
+**16. //operationMode//** \\
+Operation mode. (operationMode will be supported soon.)\\
+<WRAP group 50%>
+^Value  ^Description  ^
+|0  |Lagacy mode (Using PICC master key)  |
+|1  |New mode (Using App master key)  |
+</WRAP>
+**17. //reserved//** \\
 Reserved space.\\ \\
-**17. //byteOrder//** \\
+**18. //byteOrder//** \\
 Order of how the byte of the card is stored. When it is set as 0, will function as MSB((Most Significant Bit)). When it is set as 1, will function as LSB((Least Significant Bit)). \\ \\
-**18. //useWiegandFormat//** \\
+**19. //useWiegandFormat//** \\
 Decides whether to use Wiegand format.\\ \\
-**19. //dataType//** \\
+**20. //dataType//** \\
 Type of card data. \\
 <WRAP group 50%>
@@ Line 639: / Line 655: @@
 |3  |BCD  |
 </WRAP>
-**20. //useSecondaryKey//** \\
+**21. //useSecondaryKey//** \\
 Decides whether to use the secondary encryption key. \\ \\
-**21. //formatID//** \\
+**22. //formatID//** \\
 ID that is used when the card configuration needs to be managed from the database on the BioStar application.\\ \\
-**22. //cipher//** \\
+**23. //cipher//** \\
-Keypad로 card id를 입력받을 수 있도록 활성화 합니다. \\
+Activates 'Keypad card ID' option. \\
-기본 값은 0이며, Xpass D2 Gangbox Keypad 만 유효합니다. \\
+Default value is 0, it is only valid for XPass D2 Gangbox Keypad type. \\
 <WRAP group 50%>
-^값  ^설명  ^
+^Value  ^Description  ^
 |0  |Deactivate  |
 |1  |Activate  |
-**23. //reserved5//** \\
+**24. //reserved5//** \\
 Reserved space. \\
+</WRAP>
 ==== BS2FingerprintConfig ====
 <code cpp>