Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
en:configuration_api [2020/08/28 13:56] yjjung |
en:configuration_api [2020/09/10 09:00] yjjung [BS2AuthConfigExt] |
||
---|---|---|---|
Line 2130: | Line 2130: | ||
This parameter is not in use. \\ \\ | This parameter is not in use. \\ \\ | ||
11. //matchTimeout// \\ | 11. //matchTimeout// \\ | ||
- | 지문 인증이나 얼굴 인식에서 최대 응답 시간이며 단위는 초(sec)를 사용합니다. \\ \\ | + | The maximum response time in fingerprint or facial matching and the unit is seconds(sec). \\ \\ |
12. //authTimeout// \\ | 12. //authTimeout// \\ | ||
- | 사용자 인증의 최대 응답 시간이며 단위는 초(sec)를 사용합니다. \\ \\ | + | The maximum response time in user authentication and the unit is seconds(sec). \\ \\ |
13. //numOperators// \\ | 13. //numOperators// \\ | ||
- | 사용자 권한을 정의하는 operator의 개수입니다. \\ \\ | + | The number of operators. \\ \\ |
14. //reserved3// \\ | 14. //reserved3// \\ | ||
- | 예약된 공간입니다. \\ \\ | + | Reserved \\ \\ |
15. //userID// \\ | 15. //userID// \\ | ||
- | 사용자 식별자입니다. \\ \\ | + | User ID \\ \\ |
16. //level// \\ | 16. //level// \\ | ||
- | 사용자가 인증되었을 때 식별자에 해당하는 권한을 지정합니다. \\ | + | It specifies the corresponding level of the user when the user is authenticated.\\ |
<WRAP group 50%> | <WRAP group 50%> | ||
- | ^값 ^설명 ^ | + | ^Value ^Description ^ |
- | |0 |권한 없음 | | + | |0 |No level | |
- | |1 |관리자 권한 | | + | |1 |Operator level | |
- | |2 |시스템 구성을 변경할 수 있는 권한 | | + | |2 |System configuration level | |
- | |3 |사용자 정보를 변경할 수 있는 권한 | | + | |3 |User information level | |
</WRAP> | </WRAP> | ||
<WRAP alert> | <WRAP alert> | ||
- | **주의**\\ | + | **CAUTION**\\ |
- | Operator 추가 시, 추가하고자 하는 operator의 수를 **//numOperators//** 필드의 값으로 지정해야 합니다. | + | You must specify the number of operators to be added in the field **//numOperators//** when adding operators. |
</WRAP> | </WRAP> | ||
17. //reserved// \\ | 17. //reserved// \\ | ||
- | 예약된 공간입니다. \\ | + | Reserved \\ |
18. //reserved4// \\ | 18. //reserved4// \\ | ||
- | 예약된 공간입니다. \\ \\ | + | Reserved \\ \\ |
Line 2264: | Line 2264: | ||
</code> | </code> | ||
1. //distance// \\ | 1. //distance// \\ | ||
- | 열화상 카메라의 체온 측정 거리를 나타냅니다. 단위는 cm이며 기본값은 70 입니다. \\ \\ | + | The distance measured by the thermal imaging camera. The unit is cm, and the default is 70. \\ \\ |
2. //emissionRate// \\ | 2. //emissionRate// \\ | ||
- | 피사체가 열을 방사하는 비율을 입력합니다. \\ | + | The rate of the subject reflecting heat. \\ |
- | [95/97/98] 범위내의 입력을 권장합니다. 피사체가 사람인 경우 적정 권장은 98 입니다. \\ \\ | + | It is recommended to enter within the [95/97/98] range. If the subject is a human, 98 is recommended. \\ \\ |
3. //roi// \\ | 3. //roi// \\ | ||
- | ROI(Region of interest)는 관심영역을 의미하며, 얼굴에서 발열 측정 시, 관심 대상이되는 영역을 \\ | + | ROI (Region of interest) refers to the region of interest. \\ |
- | 좌표(x, y)와, 범위(width, height) 값을 통해서 지정할 수 있습니다. \\ \\ | + | It can be specified through coordinates (x, y) and range (width, height) values when measuring temperature on the face. \\ \\ |
4. //useBodyCompensation// \\ | 4. //useBodyCompensation// \\ | ||
- | 발열 측정된 체온의 보정을 사용할지 여부를 나타냅니다. \\ \\ | + | It decides whether to use the compensate the body temperature. \\ \\ |
5. //compensationTemperature// \\ | 5. //compensationTemperature// \\ | ||
- | 실제 체온측정값과, 카메라를 통한 체온측정은 약간의 차이가 존재할 수 있으며, 이곳에 값을 설정하여, 그 차이를 보정할 수 있습니다. \\ | + | There may be a slight difference between the actual body temperature and the body temperature measurement using the camera, and you can correct the difference by setting a value here. \\ |
- | 설정할 온도의 10을 곱한 값으로 입력하여야하며, 최소 -50에서 최대 50 사이의 값을 지정할 수 있습니다. \\ \\ | + | It must be as the value multiplied by 10 of the temperature to be set. The value is available -50 ~ +50 \\ \\ |