Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
en:configuration_api [2020/11/11 10:17] kkshin [BS2FaceConfigExt] |
en:configuration_api [2020/11/23 08:30] kkshin [BS2ThermalCameraConfig] |
||
---|---|---|---|
Line 2240: | Line 2240: | ||
Reserved \\ \\ | Reserved \\ \\ | ||
6. //thermalThresholdLow// \\ | 6. //thermalThresholdLow// \\ | ||
+ | ''Supported version : FaceStation F2 V1.0.2, FaceStation 2 V1.5.0'' \\ | ||
This is the range value for determining high temperature and must be entered as a value multiplied by 100 of the temperature to be set. \\ | This is the range value for determining high temperature and must be entered as a value multiplied by 100 of the temperature to be set. \\ | ||
Also, you can only enter in degrees Celsius. \\ | Also, you can only enter in degrees Celsius. \\ | ||
- | This value is the basis for the denial of authentication, and the setting range is between 3000(30º) and 4500(45º). \\ \\ | + | This value is the basis for the denial of authentication, and the setting range is between 3000(30º) and 4500(45º). \\ |
+ | The default value is 3200(32º), and if a value larger or smaller than the setting range is entered, the default value a set to 3200(32º). \\ | ||
+ | And you must set a value less than thermalThresholdHigh. \\ \\ | ||
7. //thermalThresholdHigh// \\ | 7. //thermalThresholdHigh// \\ | ||
This is the range value for determining high temperature and must be entered as a value multiplied by 100 of the temperature to be set. \\ | This is the range value for determining high temperature and must be entered as a value multiplied by 100 of the temperature to be set. \\ | ||
Also, you can only enter in degrees Celsius. \\ | Also, you can only enter in degrees Celsius. \\ | ||
- | This value is the basis for the denial of authentication, and the setting range is between 3000(30º) and 4500(45º). \\ \\ | + | This value is the basis for the denial of authentication, and the setting range is between 3000(30º) and 4500(45º). \\ |
+ | The default value is 3800(38º), and if a value larger or smaller than the setting range is entered, the default value a set to 3800(38º). \\ | ||
+ | And you must set a value greater than thermalThresholdLow. \\ \\ | ||
8. //maskDetectionLevel// \\ | 8. //maskDetectionLevel// \\ | ||
''FaceStation F2'' Sets the mask detection level. The detecting level is based on internal setting value. \\ | ''FaceStation F2'' Sets the mask detection level. The detecting level is based on internal setting value. \\ | ||
Line 2297: | Line 2302: | ||
</code> | </code> | ||
1. //distance// \\ | 1. //distance// \\ | ||
- | The distance measured by the thermal imaging camera. The unit is cm, and the default is 70. \\ \\ | + | The distance measured by the thermal imaging camera. The unit is cm, and the default is 100. \\ \\ |
2. //emissionRate// \\ | 2. //emissionRate// \\ | ||
- | The rate of the subject reflecting heat. \\ | + | The emissivity of the subject reflecting heat. \\ |
It is recommended to enter within the [95/97/98] range. If the subject is a human, 98 is recommended. \\ \\ | It is recommended to enter within the [95/97/98] range. If the subject is a human, 98 is recommended. \\ \\ | ||
3. //roi// \\ | 3. //roi// \\ |