Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
en:configuration_api [2022/08/11 21:34] 127.0.0.1 external edit |
en:configuration_api [2022/10/05 14:25] kateyu [BS2FaceConfig] |
||
---|---|---|---|
Line 1813: | Line 1813: | ||
[+ V2.7.1] ''FaceStation F2'' This indicates the width of the face image, and you can specify the minimum and maximum values. \\ | [+ V2.7.1] ''FaceStation F2'' This indicates the width of the face image, and you can specify the minimum and maximum values. \\ | ||
The default values of min and max are as follows. \\ | The default values of min and max are as follows. \\ | ||
- | <WRAP group 20%> | + | [+ 2.8.3] ''BioStation 3'' The settings are ignored. \\ |
- | ^ ^Default ^ | + | <WRAP group 30%> |
- | |min |66 | | + | ^ ^Default(min) ^Default(max) ^ |
- | |max |250 | | + | |FSF2 |66 |250 | |
+ | |BS3 |- |- | | ||
</WRAP> | </WRAP> | ||
Line 1822: | Line 1823: | ||
[+ V2.7.1] ''FaceStation F2'' Represents the face search range, and you can specify the x value (horizontal coordinate) of the range and the width from the x value point. \\ | [+ V2.7.1] ''FaceStation F2'' Represents the face search range, and you can specify the x value (horizontal coordinate) of the range and the width from the x value point. \\ | ||
The default values of x and width are as follows. \\ | The default values of x and width are as follows. \\ | ||
- | <WRAP group 20%> | + | [+ 2.8.3] ''BioStation 3'' The settings are ignored. \\ |
- | ^ ^Default ^ | + | <WRAP group 30%> |
- | |x |144 | | + | ^ ^Default(x) ^Default(width) ^ |
- | |width |432 | | + | |FSF2 |144 |432 | |
+ | |BS3 |- |- | | ||
</WRAP> | </WRAP> | ||
- | 14. //reserved2// \\ | + | |
+ | **14. //detectDistance//** \\ | ||
+ | [+ 2.8.3] ''BioStation 3'' This configures the minimum and maximum detection range for facial recognition. \\ | ||
+ | We no longer support faceWidth to pinpoint the face location using pixel units due to its complexity. \\ | ||
+ | Instead, we set the detection range of the subject(face). The unit is set to cm, and the value must be inputted as a multiple of 10. \\ | ||
+ | <WRAP group 80%> | ||
+ | ^ ^Min limit for min detection range ^Max limit for min detection range ^Min detection range(Default) ^Min limit for max detection range ^Max limit for max detection range ^Max sensing range(No limit) ^Max sensing range(Default) ^ | ||
+ | |BS3 |30 |100 |60 |40 |100 |255 |100 | | ||
+ | </WRAP> | ||
+ | |||
+ | **15. //wideSearch//** \\ | ||
+ | [+ 2.8.3] ''BioStation 3'' This can increase the detection range for facial recognition. \\ | ||
+ | We no longer support searchRange to set the x-coordinate and width due to its complexity. \\ | ||
+ | Instead, we set the face detection setting as default(FALSE), or a wide area(TRUE). \\ | ||
+ | The details of the settings and protocols for the detection of wide area is set within the device, which the user cannot change. \\ \\ | ||
+ | If this setting is set to TRUE, the camera detects subjects within a large range, and unintentionally detect and authenticate multiple subjects at once. Therefore, the default setting is at FALSE. \\ \\ | ||
+ | |||
+ | 16. //unused// \\ | ||
+ | Reserved space.\\ \\ | ||
+ | 17. //reserved// \\ | ||
Reserved space.\\ \\ | Reserved space.\\ \\ | ||
==== BS2Rs485ConfigEX ==== | ==== BS2Rs485ConfigEX ==== | ||
Line 2568: | Line 2589: | ||
13. //reserved2// \\ | 13. //reserved2// \\ | ||
Reserved Space. \\ \\ | Reserved Space. \\ \\ | ||
+ | |||
+ | ==== BS2VoipConfigExt ==== | ||
+ | <code cpp> | ||
+ | typedef struct { | ||
+ | BS2_USER_ID phoneNumber; | ||
+ | char description[48 * 3]; | ||
+ | |||
+ | uint8_t reserved[32]; | ||
+ | } BS2ExtensionNumber; | ||
+ | |||
+ | typedef struct { | ||
+ | BS2_BOOL enabled; | ||
+ | BS2_BOOL useOutboundProxy; | ||
+ | uint16_t registrationDuration; | ||
+ | |||
+ | BS2_URL address; | ||
+ | BS2_PORT port; | ||
+ | |||
+ | struct { | ||
+ | uint8_t speaker; // 0 ~ 100 | ||
+ | uint8_t mic; // 0 ~ 100 | ||
+ | } volume; ///< 2 bytes | ||
+ | |||
+ | BS2_USER_ID id; | ||
+ | BS2_USER_ID password; | ||
+ | BS2_USER_ID authorizationCode; | ||
+ | |||
+ | struct { | ||
+ | BS2_URL address; | ||
+ | BS2_PORT port; | ||
+ | uint8_t reserved[2]; | ||
+ | } outboundProxy; | ||
+ | |||
+ | uint8_t exitButton; /// *, #, 0~9 | ||
+ | uint8_t reserved1; | ||
+ | uint8_t numPhoneBook; | ||
+ | BS2_BOOL showExtensionNumber; | ||
+ | |||
+ | BS2ExtensionNumber phonebook[128]; | ||
+ | |||
+ | uint8_t reserved2[32]; ///< 32 bytes (reserved) | ||
+ | } BS2VoipConfigExt; | ||
+ | </code> | ||
+ | 1. //phoneNumber// \\ | ||
+ | This is the extension. \\ \\ | ||
+ | 2. //description// \\ | ||
+ | Display information. \\ \\ | ||
+ | 3. //reserved// \\ | ||
+ | Reserved space. \\ \\ | ||
+ | 4. //enabled// \\ | ||
+ | Sets whether the VoIP extension feature is enabled. \\ \\ | ||
+ | 5. //useOutboundProxy// \\ | ||
+ | Sets whether the Outbound Proxy Server is configured. \\ \\ | ||
+ | 6. //registrationDuration// \\ | ||
+ | The cycle of updating the relevant information to the SIP server. \\ | ||
+ | Set in seconds and must be between 60 and 600. \\ \\ | ||
+ | 7. //address// \\ | ||
+ | Enter the IP address of the SIP server (usually BioStar). \\ \\ | ||
+ | 8. //port// \\ | ||
+ | Enter the SIP server port. The default port is 5060. \\ \\ | ||
+ | 9. //speaker// \\ | ||
+ | Enter the speaker volume information for the intercom in the range 0 to 100. The default value is 50. \\ \\ | ||
+ | 10. //mic// \\ | ||
+ | Enter the microphone volume information for the intercom in the range 0 to 100. The default value is 50. \\ \\ | ||
+ | 11. //id// \\ | ||
+ | Enter the ID to connect to the SIP server. \\ | ||
+ | 12. //password// \\ | ||
+ | Specifies the password to connect to the SIP server. \\ \\ | ||
+ | 13. //authorizationCode// \\ | ||
+ | The authentication code value required to connect to the SIP server. \\ \\ | ||
+ | 14. //outboundProxy// \\ | ||
+ | Enter Outbound proxy server information. \\ \\ | ||
+ | 15. //address// \\ | ||
+ | Enter the IP address of the Outbound Proxy Server. \\ \\ | ||
+ | 16. //port// \\ | ||
+ | Enter the Outbound Proxy Server port. \\ \\ | ||
+ | 17. //reserved// \\ | ||
+ | Reserved space. \\ \\ | ||
+ | 18. //exitButton// \\ | ||
+ | Button symbol to be used as a check-out button. \\ | ||
+ | <WRAP group 50%> | ||
+ | ^Value ^Description ^ | ||
+ | |* |'*' ASCII code 42 | | ||
+ | |# |'#' ASCII code 35 | | ||
+ | |0~9 |'0'~'9' ASCII code (48~57) | | ||
+ | </WRAP> | ||
+ | 19. //reserved1// \\ | ||
+ | Reserved space. \\ \\ | ||
+ | 20. //numPhoneBook// \\ | ||
+ | Number of phone books. \\ \\ | ||
+ | 21. //showExtensionNumber// \\ | ||
+ | Determines whether to show the phone book. \\ \\ | ||
+ | 22. //phonebook// \\ | ||
+ | You can specify up to 128 extensions in your phone book. \\ \\ | ||
+ | 23. //reserved2// \\ | ||
+ | Reserved space. \\ \\ | ||
+ | |||
+ | |||
+ | ==== BS2RtspConfig ==== | ||
+ | <code cpp> | ||
+ | typedef struct { | ||
+ | BS2_USER_ID id; | ||
+ | BS2_USER_ID password; | ||
+ | |||
+ | BS2_URL address; | ||
+ | |||
+ | BS2_PORT port; | ||
+ | BS2_BOOL enabled; | ||
+ | uint8_t reserved; | ||
+ | |||
+ | uint8_t reserved2[32]; | ||
+ | } BS2RtspConfig; | ||
+ | </code> | ||
+ | 1. //id// \\ | ||
+ | Account information when connecting to the RTSP server. \\ \\ | ||
+ | 2. //password// \\ | ||
+ | Password when connecting to the RTSP server. \\ \\ | ||
+ | 3. //address// \\ | ||
+ | Enter the address of the RTSP server. \\ \\ | ||
+ | 4. //port// \\ | ||
+ | Enter the RTSP server connection port. The default port is 554. \\ \\ | ||
+ | 5. //enabled// \\ | ||
+ | Sets whether an RTSP connection is enabled. \\ \\ | ||
+ | 6. //reserved// \\ | ||
+ | Reserved space. \\ \\ | ||
+ | 7. //reserved2// \\ | ||
+ | Reserved space. \\ \\ | ||
+ |