Differences
This shows you the differences between two versions of the page.
Next revision | Previous revision | ||
en:how_to_configure_an_interlock_zone [2018/04/02 20:59] kate created |
en:how_to_configure_an_interlock_zone [2024/01/23 02:23] (current) kate |
||
---|---|---|---|
Line 1: | Line 1: | ||
====== How to Configure an Interlock Zone ====== | ====== How to Configure an Interlock Zone ====== | ||
- | To provide secure interlock area, one of the door is locked when an external input such as door status sensor indicates another door is opened. This feature is usually considered important in laboratory or operation room where security of dust is of high concern. | + | To provide a secure interlock area, one of the doors must be locked when the external input, such as door status sensor, indicates that the other door is opened. This feature is usually considered important in laboratories or operation rooms where security of dust is of high concern. |
{{:en:interlock.png?600|}} | {{:en:interlock.png?600|}} | ||
Line 15: | Line 15: | ||
CoreStation should be a RS485 Master of the local zone | CoreStation should be a RS485 Master of the local zone | ||
- | FW : cs40_v1_1_0_20180317_sign or higher version | + | FW : v1.1.0 or higher version |
- | The interlock zone will be supported by CoreStation firmware. It means that you can use any devices for Interlock Zone Configuration as slave device of CoreStation. | + | The interlock zone will be supported by CoreStation firmware. It means that you can use any devices for Interlock Zone Configuration as slave devices of CoreStation. |
+ | |||
+ | Please note that Corestation does not support FaceStation F2 and BioStation 3 as Slave devices. | ||
</callout> | </callout> | ||
{{ :en:interlock_zone.mp4?800x450 |}} | {{ :en:interlock_zone.mp4?800x450 |}} | ||
- | 1. Activate the license of BioStar2 AC as standard or higher level | + | 1. Activate BioStar 2 AC license as standard or higher level |
- | For license inquiry, please contact to our sales representative. | + | For license inquiries, please contact to our sales representative. |
- | 2. Confirm the zone menu | + | 2. Confirm the **zone** menu |
- | 3. Go to Device menu | + | 3. Go to **Device** menu |
- | 4. Add CoreStation and slave devices | + | 4. Add CoreStation and its slave devices |
{{:en:interlock_device.png?600|}} | {{:en:interlock_device.png?600|}} | ||
Line 45: | Line 47: | ||
9. Add Interlock Zone | 9. Add Interlock Zone | ||
- | 10. Configure the door of Interlock Zone | + | 10. Configure the door of the Interlock Zone |
- | - You can select up to 4 doors. | + | <callout type="primary" icon="true"> |
+ | You can select up to 4 doors. | ||
+ | </callout> | ||
{{:en:interlock_door2.png?600|}} | {{:en:interlock_door2.png?600|}} | ||
- | 11. If you would like to make an alert sound or output signal, set an alarm of Interlock zone | + | 11. If you would like to make an alert sound or output signal, set an alarm of the Interlock zone |
{{:en:interlock_alert.png?600|}} | {{:en:interlock_alert.png?600|}} | ||
- | 12. To confirm the configuration of Interlock setting, go to Monitoring | + | 12. To confirm the configuration of the Interlock setting, go to **Monitoring** |
- | 13. Open one of the doors and keep the opened status, and then try to authentication to same door | + | 13. Open one of the doors and keep the opened status, then try to authentication to same door |
14. Confirm the [Interlock door open denied alarm] as follows | 14. Confirm the [Interlock door open denied alarm] as follows |