Differences
This shows you the differences between two versions of the page.
| Next revision | Previous revision | ||
|
en:how_to_synchronize_devices_with_the_server [2017/10/11 11:51] 127.0.0.1 external edit |
en:how_to_synchronize_devices_with_the_server [2021/12/17 09:54] (current) peterk |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| - | {{tag>"System Configuration" "BioStar 2" "Alarm Zone"}} | + | {{tag>"System Configuration" "BioStar 2" "Synchronization" }} |
| - | Alarm zone has introduced with BioStar 2.5. It is used to detect any attempts of intrusion during an armed status. \\ | + | ====== How to synchronize devices with the server ====== |
| - | You can trigger the device to make sounds or send a relay on the event of an intrusion.\\ | + | You may have seen your device with a yellow symbol on the device menu once you connected the device to the server. \\ |
| - | This is basically something you would turn on at the end of the day after closing your offices and you would disarm the device when you start work on the next day. \\ | + | {{:en:2x_sysconfig_device_synchronization_001.png?nolink&600|}} \\ |
| - | {{:en:2x_sysconfig_alarm_zone_001.png?450|}}\\ | + | This means that the device has different access groups, doors, zone, and user information than the server. \\ |
| - | Refer to the bottom of the article to see which devices support this zone. \\ | + | In BioStar 2.5, device synchronization is automatic on device reconnection if you turned automatic user synchronization on. \\ |
| + | This means that when a device disconnected from the server, you had to click sync again in previous devices to synchronize the devices with the server but now it is automatically taken care of. \\ | ||
| - | Note that only local zone with RS485 connection is supported right now. Global zone, which would be server matching of the zone information is currently unavailable. \\ | + | From BioStar 2.7.1, a new device synchronization has been supported. \\ |
| + | If you choose 'All Devices (including user update from the device)’, you can update some user information when you modify from the device directly. \\ | ||
| - | The alarm zone can detect intrusion based on the configured input and the sensor of the door is also used for detecting intrusion. \\ | + | From BioStar 2.7.11, 'Specific Devices (Only devices belonging to the access group)' has been included. \\ |
| + | This is a partial auto user synchronization mode that depends on the access group configuration. \\ | ||
| - | You can configure various output and sound for the Alarm status. In the Trigger & Action menu you can configure the zone settings so that an email is sent to the administrator on a specific event. \\ | + | To get more detailed information, please check the linked document. ([[en:specific_devices_only_devices_belonging_to_the_access_group_option|'Specific Devices(Only Devices Belonging to the Access Group)' Option]]) \\ |
| + | ===== Configuring Automatic User Synchronization ===== | ||
| - | During an armed status, users will be unable to enter and an attempt to authenticate will be logged as intrusion alarm access denied. For further information on the types of event logs, please refer to the knowledge base configuration guide regarding Alarm Zone. \\ | + | 1. Log in to BioStar 2 with an administrator account. \\ |
| + | 2. Click **Setting**. \\ | ||
| - | ====== How to Configure an Alarm Zone ====== | + | 3. Click **SERVER.** \\ |
| - | 1. Add a device to BioStar 2. \\ | + | {{:en:2x_sysconfig_device_synchronization_002.png?nolink&600|}} \\ |
| - | 2. Add the device to a door. \\ | + | 4. On **User/Device Management** > **Automatic User Synchronization**. \\ |
| - | Refer to door configuration link http://kb.supremainc.com/knowledge/doku.php?id=en:how_to_make_doors | + | {{:en:usersync_2.7.12.png?nolink&600|}} \\ |
| - | \\ | + | |
| - | + | ||
| - | 3. Click the **ZONE** menu. \\ | + | |
| - | + | ||
| - | 4. Click **ADD ZONE**. \\ | + | |
| - | + | ||
| - | {{:en:2x_sysconfig_alarm_zone_002.png?250|}}\\ | + | |
| - | + | ||
| - | <callout type="primary" icon="true"> | + | |
| - | You need a BioStar 2 AC Standard License to use the Zone menu. | + | |
| - | </callout> | + | |
| + | 5. Choose the synchronization mode which you want and click **Apply**. \\ | ||
| - | 5. Select Intrusion Alarm and click **Apply**. \\ | ||
| - | |||
| - | {{:en:2x_sysconfig_alarm_zone_003.png?650|}}\\ | ||
| - | |||
| - | 6. Select a **Name** for your Alarm zone. \\ | ||
| - | |||
| - | <callout type="primary" icon="true"> | ||
| - | Currently only Local Mode (RS-485 connection) is available with BioStar 2.5. | ||
| - | </callout> | ||
| - | |||
| - | 7. Select your **Door** that will sense the intrusion. \\ | ||
| - | |||
| - | 8. Set the Zone to **Active**. \\ | ||
| - | |||
| - | 9. Set the **Delay Time** as required. \\ | ||
| - | |||
| - | <callout type="primary" icon="true"> | ||
| - | Arm Delay Time: device will wait and make a beep sound for the number of seconds configured before arming. \\ | ||
| - | |||
| - | Disarm Delay Time: device will not make an alarm action on **Intrusion alarm detected** event for the configured number of seconds when intrusion is detected. </callout> | ||
| - | |||
| - | 10. Click **+Add** to choose the method to arm/disarm the device. \\ | ||
| - | |||
| - | <callout type="primary" icon="true"> | ||
| - | There are 3 methods to arm/disarm the device \\ | ||
| - | |||
| - | 1. **Access Card**: This will require registering a CSN/Wiegand Card for arming and user authentication to arm/disarm the device. You can make up to 128 Access Cards.\\ | ||
| - | |||
| - | 2. **Device**: This option is available for devices that have a keypad. \\ | ||
| - | |||
| - | - A2: Press the red Arm button that appears on the LCD screen beside the menu button. Press the same button to disarm. \\ | ||
| - | |||
| - | - BioStation 2, BioStation L2: Press F1 for 1 second to arm and press F2 for 1 second. \\ | ||
| - | |||
| - | 3. **Input**: Use this option to arm/disarm a device with external input signals. | ||
| - | </callout> | ||
| - | |||
| - | 11. Choose the **Access Group** that will be able to arm/disarm the zone. Up to 128 access groups may be configured. \\ | ||
| - | |||
| - | {{:en:2x_sysconfig_alarm_zone_004.png?800|}}\\ | ||
| - | |||
| - | 12. Configure the input to detect intrusion by clicking **+Add**. The door sensor is also used to detect intrusion. \\ | ||
| - | {{:en:2x_sysconfig_alarm_zone_005.png?800|}}\\ | ||
| - | |||
| - | 13. Configure the Alarm to trigger on a specific event by clicking +Add and choosing your option. You can configure a sound to be made by the device or send an output relay. | ||
| - | |||
| - | The events shown in the image below are the events available for the Alarm zone. \\ | ||
| - | |||
| - | {{:en:2x_sysconfig_alarm_zone_006.png?800|}}\\ | ||
| - | |||
| - | |||
| - | ====== Video Demonstration ====== | ||
| - | |||
| - | Below is a sample video of arming an A2 with device arm/disarm setting. An authentication attempt is made during arm status. Then the zone is disarmed. \\ | ||
| - | {{:en:2x_sysconfig_a2_alarm_final.mp4|}} \\ | ||
| - | |||
| - | <callout type="warning" icon="true"> | ||
| - | You can clear the alarm in the **Zone Status** tab of the **Monitoring** page but you cannot disable the arm status within BioStar 2’s menu. </callout> | ||
| - | |||
| - | ====== Supported Devices ====== | ||
| - | |||
| - | Below are the devices that support alarm zone in BioStar 2.5: \\ | ||
| - | |||
| - | - BioStation 2 FW 1.5.0 \\ | ||
| - | - BioStation A2 FW 1.4.0 \\ | ||
| - | - CoreStation FW 1.0.0 \\ | ||
| - | - P2 FW 1.0.0 \\ | ||
| - | - R2 FW 1.0.0 \\ | ||
| - | |||
| - | The devices below will support alarm zone in the future (end of 2017): | ||
| - | |||
| - | - BioStation L2 FW 1.3.0 | ||
| - | - W2 FW 1.2.0 | ||
| - | - FaceStation 2 FW 1.1.0 | ||
| - | |||
| - | Other entry devices do not support this zone. \\ | ||