Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
|
en:log_management_api [2021/05/26 15:26] kkshin [BS2Event] |
en:log_management_api [2021/08/07 14:44] kkshin [BS2Event] |
||
|---|---|---|---|
| Line 74: | Line 74: | ||
| uint8_t reserved[12]; | uint8_t reserved[12]; | ||
| } interlock; | } interlock; | ||
| + | struct { | ||
| + | uint16_t relayPort; | ||
| + | uint16_t inputPort; | ||
| + | uint8_t reserved[28]; | ||
| + | } relayAction; | ||
| }; | }; | ||
| union { | union { | ||
| Line 133: | Line 138: | ||
| **15. //interlock.doorID//** \\ | **15. //interlock.doorID//** \\ | ||
| Door ID that makes interlock zone alarms. \\ \\ | Door ID that makes interlock zone alarms. \\ \\ | ||
| - | **16. //subCode//** \\ | + | **16. //relayAction.relayPort//** \\ |
| + | Relay port identifier when IM-120 RelayAction takes place. \\ \\ | ||
| + | **17. //relayAction.inputPort//** \\ | ||
| + | Relay port identifier when IM-120 RelayAction takes place. \\ \\ | ||
| + | **18. //subCode//** \\ | ||
| Sub code value of log types. Use if the additional information is necessary. \\ | Sub code value of log types. Use if the additional information is necessary. \\ | ||
| - | ^Category ^Event code ^Value ^Description ^ | + | ^Category ^Event code ^Value ^Description ^ |
| |Verify |BS2_SUB_EVENT_VERIFY_ID_PIN |0x01 |ID and PIN verification success | | |Verify |BS2_SUB_EVENT_VERIFY_ID_PIN |0x01 |ID and PIN verification success | | ||
| |::: |BS2_SUB_EVENT_VERIFY_ID_FINGER |0x02 |ID and fingerprint verification success | | |::: |BS2_SUB_EVENT_VERIFY_ID_FINGER |0x02 |ID and fingerprint verification success | | ||
| Line 185: | Line 194: | ||
| |APB |BS2_SUB_EVENT_ZONE_HARD_APB |0x01 |Hard APB zone | | |APB |BS2_SUB_EVENT_ZONE_HARD_APB |0x01 |Hard APB zone | | ||
| |::: |BS2_SUB_EVENT_ZONE_SOFT_APB |0x02 |Soft APB zone | | |::: |BS2_SUB_EVENT_ZONE_SOFT_APB |0x02 |Soft APB zone | | ||
| - | + | **19. //mainCode//** \\ | |
| - | **17. //mainCode//** \\ | + | |
| Main code value of log types. \\ | Main code value of log types. \\ | ||
| ^Category ^Event code ^Value ^Description ^ | ^Category ^Event code ^Value ^Description ^ | ||
| Line 268: | Line 276: | ||
| |::: |BS2_EVENT_ZONE_SCHEDULED_LOCK_ALARM |0x6E00 |Scheduled lock alarm zone start | | |::: |BS2_EVENT_ZONE_SCHEDULED_LOCK_ALARM |0x6E00 |Scheduled lock alarm zone start | | ||
| |::: |BS2_EVENT_ZONE_SCHEDULED_LOCK_ALARM_CLEAR |0x6F00 |Scheduled lock alarm zone clear | | |::: |BS2_EVENT_ZONE_SCHEDULED_LOCK_ALARM_CLEAR |0x6F00 |Scheduled lock alarm zone clear | | ||
| + | | | ||
| + | |RelayAction |BS2_EVENT_RELAY_ACTION_ON |0xC300 |RelayAction Switch-ON | | ||
| + | |::: |BS2_EVENT_RELAY_ACTION_OFF |0xC400 |RelayAction Switch-OFF | | ||
| + | |::: |BS2_EVENT_RELAY_ACTION_KEEP |0xC500 |RelayAction KEEP SIGNAL | | ||
| + | |||
| - | **18. //param//** \\ | + | **20.//param//** \\ |
| It is used only when extra information on the device is needed. Usually, a time and attendance code, a port number of the door or input device is stored in the //param// argument. | It is used only when extra information on the device is needed. Usually, a time and attendance code, a port number of the door or input device is stored in the //param// argument. | ||
| When a time and attendance code is stored, refer to the following values: | When a time and attendance code is stored, refer to the following values: | ||
| Line 311: | Line 324: | ||
| \\ \\ | \\ \\ | ||
| - | **19. //image//** \\ | + | **21. //image//** \\ |
| Prior to SDK V2.6.0, it used the whole 1 byte and means below: \\ | Prior to SDK V2.6.0, it used the whole 1 byte and means below: \\ | ||
| - Whether the image was included when the event occurred (true / false). \\ \\ | - Whether the image was included when the event occurred (true / false). \\ \\ | ||