

This is an old revision of the document!
Log Management API
API that controls the device log.
- BS2_GetLog: Gets certain amount of logs.
- BS2_GetFilteredLog: Gets filtered logs.
- BS2_ClearLog: Deletes all logs.
- BS2_StartMonitoringLog: Starts Real-time log streaming.
- BS2_StartMonitoringLogEx: [+ V2.7.1] Starts Real-time log streaming including the temperature information.
- BS2_StopMonitoringLog: Stops Real-time log streaming.
- BS2_GetLogBlob: Gets certain amount of logs based on the event mask.
- BS2_GetFilteredLogSinceEventId: Gets filtered logs.
- BS2_GetImageLog : Gets image logs using event ID.
- BS2_GetLogSmallBlob: [+ 2.6.4] Gets certain amount of logs based on the event mask in an efficient way.
- BS2_GetLogSmallBlobEx: [+ 2.7.1] Gets certain amount of logs based on the event mask in an efficient way, including the temperature information.
Callback Function
OnLogReceived
장치로부터 새로운 로그를 수신했을 때 호출되는 콜백 함수입니다.
typedef void (*OnLogReceived)(uint32_t deviceId, BS2Event* log);
1. deviceId
새로운 로그를 보내준 장치 ID입니다.
2. log
새로운 로그 정보 구조체입니다.
OnLogReceivedEx
[+ V2.7.1] 장치로부터 새로운 로그를 수신했을 때 호출되는 콜백 함수입니다.
열화상 카메라를 통해 측정된 체온이 세번째 인자로 수신되며, BS2FaceConfigExt의 auditTemperature가 true로 설정되어져야 합니다.
typedef void (*OnLogReceivedEx)(uint32_t deviceId, BS2Event* log, uint32_t temperature);
1. deviceId
새로운 로그를 보내준 장치 ID입니다.
2. log
새로운 로그 정보 구조체입니다.
3. temperature
새로운 로그 발생 시, 측정된 체온 정보입니다.
Structure
BS2Event
typedef struct { uint32_t id; uint32_t dateTime; uint32_t deviceID; union { char userID[BS2_USER_ID_SIZE]; uint32_t uid; uint32_t doorID; uint32_t liftID; uint32_t zoneID; struct { uint32_t ioDeviceID; uint16_t port; int8_t value; uint8_t reserved[25]; }; struct { uint32_t zoneID; uint32_t doorID; uint32_t ioDeviceID; uint16_t port; uint8_t reserved[18]; } alarm; struct { uint32_t zoneID; uint32_t doorID[4]; uint8_t reserved[12]; } interlock; }; union { uint16_t code; struct { uint8_t subCode; uint8_t mainCode; }; }; uint8_t param; #ifdef LESS_THAN_SDK_2_6_0 BS2_BOOL image; // Deprecated in V2.6.0 #else uint8_t image: 1; // Support image and DST by bit division uint8_t isDST: 1; uint8_t half: 1; uint8_t hour: 4; uint8_t negative: 1; #endif } BS2Event;
1. id
Log record ID which automatically increases from 1 when the log is generated.
2. dateTime
The time when the log has been generated. It means the seconds past from UTC until the current time.
3. deviceID
ID of the device that generated the log.
4. userID
User ID related to log. When the value is 0, the log is not relevant to user.
5. uid
You can refer to doorID regarding door log, zoneID regarding zone log.
If you do not know exactly then you can refer to uid.
Since uid, doorID, liftID, zoneID are declared as union, basically it means information such as unordered list.
6. doorID
ID of the door that generated the log.
7. liftID
ID of the lift that generated the log.
8. zoneID
ID of the zone that generated the log.
9. ioDeviceID
Door or Input device ID. When the value is 0, the log is not relevant to Door or Input device.
10. port
Port for ioDeviceID.
11. value
Port value for ioDeviceID and means below.
BS2_PORT_VALUE_UNKNOWN : -1
BS2_PORT_VALUE_OPEN : 0
BS2_PORT_VALUE_CLOSED : 1
BS2_PORT_VALUE_SUPERVISED_SHORT : 2
BS2_PORT_VALUE_SUPERVISED_OPEN : 3
12. alarm.zoneID
Zone ID that makes intrusion alarm zone alarms.
13. alarm.doorID
Door ID that makes intrusion alarm zone alarms.
14. interlock.zoneID
Zone ID that makes interlock zone alarms.
15. interlock.doorID
Door ID that makes interlock zone alarms.
16. subCode
Sub code value of log types. Use if the additional information is necessary.
Category | Event code | Value | Description |
---|---|---|---|
Verify | BS2_SUB_EVENT_VERIFY_ID_PIN | 0x01 | ID and PIN verification success |
BS2_SUB_EVENT_VERIFY_ID_FINGER | 0x02 | ID and fingerprint verification success | |
BS2_SUB_EVENT_VERIFY_ID_FINGER_PIN | 0x03 | ID, fingerprint, and PIN verification success | |
BS2_SUB_EVENT_VERIFY_ID_FACE | 0x04 | ID and face verification success | |
BS2_SUB_EVENT_VERIFY_ID_FACE_PIN | 0x05 | ID, face, and PIN verification success | |
BS2_SUB_EVENT_VERIFY_CARD | 0x06 | Card verification success | |
BS2_SUB_EVENT_VERIFY_CARD_PIN | 0x07 | Card and PIN verification success | |
BS2_SUB_EVENT_VERIFY_CARD_FINGER | 0x08 | Card and fingerprint verification success | |
BS2_SUB_EVENT_VERIFY_CARD_FINGER_PIN | 0x09 | Card, fingerprint, and PIN verification success | |
BS2_SUB_EVENT_VERIFY_CARD_FACE | 0x0A | Card and face verification success | |
BS2_SUB_EVENT_VERIFY_CARD_FACE_PIN | 0x0B | Card, PIN, and face verification success | |
BS2_SUB_EVENT_VERIFY_AOC | 0x0C | AOC card verification success | |
BS2_SUB_EVENT_VERIFY_AOC_PIN | 0x0D | AOC card and PIN verification success | |
BS2_SUB_EVENT_VERIFY_AOC_FINGER | 0x0E | AOC card and fingerprint verification success | |
BS2_SUB_EVENT_VERIFY_AOC_FINGER_PIN | 0x0F | AOC card, fingerprint, PIN verification success | |
Identify | BS2_SUB_EVENT_IDENTIFY_FINGER | 0x01 | Fingerprint identification success |
BS2_SUB_EVENT_IDENTIFY_FINGER_PIN | 0x02 | Fingerprint and PIN identification success | |
BS2_SUB_EVENT_IDENTIFY_FACE | 0x03 | Face identification success | |
BS2_SUB_EVENT_IDENTIFY_FACE_PIN | 0x04 | Face and PIN identification success | |
Auth | BS2_SUB_EVENT_DUAL_AUTH_FAIL_TIMEOUT | 0x01 | Dual authentication timeout |
BS2_SUB_EVENT_DUAL_AUTH_FAIL_ACCESS_GROUP | 0x02 | Attempted the dual authentication with invalid user | |
Credential | BS2_SUB_EVENT_CREDENTIAL_ID | 0x01 | Invalid user ID |
BS2_SUB_EVENT_CREDENTIAL_CARD | 0x02 | Invalid card | |
BS2_SUB_EVENT_CREDENTIAL_PIN | 0x03 | Invalid PIN | |
BS2_SUB_EVENT_CREDENTIAL_FINGER | 0x04 | Invalid fingerprint | |
BS2_SUB_EVENT_CREDENTIAL_FACE | 0x05 | Invalid face | |
BS2_SUB_EVENT_CREDENTIAL_AOC_PIN | 0x06 | Invalid AOC PIN | |
BS2_SUB_EVENT_CREDENTIAL_AOC_FINGER | 0x07 | Invalid AOC fingerprint | |
Auth | BS2_SUB_EVENT_AUTH_FAIL_INVALID_AUTH_MODE | 0x01 | Invalid authentication mode |
BS2_SUB_EVENT_AUTH_FAIL_INVALID_CREDENTIAL | 0x02 | Non-registered authentication method | |
BS2_SUB_EVENT_AUTH_FAIL_TIMEOUT | 0x03 | Authentication timeout | |
Access | BS2_SUB_EVENT_ACCESS_DENIED_ACCESS_GROUP | 0x01 | Access was denied because the user has not been registered for the access group |
BS2_SUB_EVENT_ACCESS_DENIED_DISABLED | 0x02 | Access was denied because the user is inactive | |
BS2_SUB_EVENT_ACCESS_DENIED_EXPIRED | 0x03 | Access was denied because the user entry period was expired | |
BS2_SUB_EVENT_ACCESS_DENIED_ON_BLACKLIST | 0x04 | Access was denied because the card is on the blacklist | |
BS2_SUB_EVENT_ACCESS_DENIED_APB | 0x05 | Access was denied because the user has violated the anti-passback rule | |
BS2_SUB_EVENT_ACCESS_DENIED_TIMED_APB | 0x06 | Access was denied because the user tried to enter the timed anti-passback zone within the limited time frame | |
BS2_SUB_EVENT_ACCESS_DENIED_FORCED_LOCK | 0x07 | Access was denied because the zone was forced to be locked | |
APB | BS2_SUB_EVENT_ZONE_HARD_APB | 0x01 | Hard APB zone |
BS2_SUB_EVENT_ZONE_SOFT_APB | 0x02 | Soft APB zone |
17. mainCode
Main code value of log types.
Category | Event code | Value | Description |
---|---|---|---|
Auth | BS2_EVENT_VERIFY_SUCCESS | 0x1000 | 1:1 authentication success |
BS2_EVENT_VERIFY_FAIL | 0x1100 | 1:1 authentication fail | |
BS2_EVENT_VERIFY_DURESS | 0x1200 | 1:1 duress authentication success | |
BS2_EVENT_IDENTIFY_SUCCESS | 0x1300 | 1:N authentication success | |
BS2_EVENT_IDENTIFY_FAIL | 0x1400 | 1:N authentication fail | |
BS2_EVENT_IDENTIFY_DURESS | 0x1500 | 1:N duress authentication success | |
BS2_EVENT_DUAL_AUTH_SUCCESS | 0x1600 | Dual authentication success | |
BS2_EVENT_DUAL_AUTH_FAIL | 0x1700 | Dual authentication fail | |
BS2_EVENT_AUTH_FAILED | 0x1800 | Attempted to authenticate with the non-registered credential | |
BS2_EVENT_ACCESS_DENIED | 0x1900 | Invalid user attempted to authenticate or user violated the APB rule | |
BS2_EVENT_FAKE_FINGER_DETECTED | 0x1A00 | Fake fingerprint detection | |
User | BS2_EVENT_USER_ENROLL_SUCCESS | 0x2000 | User enroll success |
BS2_EVENT_USER_ENROLL_FAIL | 0x2100 | User enroll fail | |
BS2_EVENT_USER_UPDATE_SUCCESS | 0x2200 | User update success | |
BS2_EVENT_USER_UPDATE_FAIL | 0x2300 | User update fail | |
BS2_EVENT_USER_DELETE_SUCCESS | 0x2400 | User delete success | |
BS2_EVENT_USER_DELETE_FAIL | 0x2500 | User delete fail | |
BS2_EVENT_USER_DELETE_ALL_SUCCESS | 0x2600 | Delete all user success | |
BS2_EVENT_USER_ISSUE_AOC_SUCCESS | 0x2700 | Authentication success with access card | |
BS2_EVENT_USER_DUPLICATE_CREDENTIAL | 0x2800 | Duplicated credential(Card/Fingerprint/Face) detection | |
Device | BS2_EVENT_DEVICE_SYSTEM_RESET | 0x3000 | System reset |
BS2_EVENT_DEVICE_SYSTEM_STARTED | 0x3100 | System started | |
BS2_EVENT_DEVICE_TIME_SET | 0x3200 | System time set | |
BS2_EVENT_DEVICE_TIMEZONE_SET | 0x3201 | Time zone chagned | |
BS2_EVENT_DEVICE_DST_SET | 0x3202 | DST setting changed | |
BS2_EVENT_DEVICE_LINK_CONNECTED | 0x3300 | LAN cable connected | |
BS2_EVENT_DEVICE_LINK_DISCONNETED | 0x3400 | LAN cable disconnected | |
BS2_EVENT_DEVICE_DHCP_SUCCESS | 0x3500 | IP address allocated by DHCP | |
BS2_EVENT_DEVICE_ADMIN_MENU | 0x3600 | Open administrator menu | |
BS2_EVENT_DEVICE_UI_LOCKED | 0x3700 | Screen locked | |
BS2_EVENT_DEVICE_UI_UNLOCKED | 0x3800 | Screen unlocked | |
BS2_EVENT_DEVICE_COMM_LOCKED | 0x3900 | RS485 communication locked | |
BS2_EVENT_DEVICE_COMM_UNLOCKED | 0x3A00 | RS485 communication unlocked | |
BS2_EVENT_DEVICE_TCP_CONNECTED | 0x3B00 | TCP connected | |
BS2_EVENT_DEVICE_TCP_DISCONNECTED | 0x3C00 | TCP disconnected | |
BS2_EVENT_DEVICE_RS485_CONNECTED | 0x3D00 | RS485 connected | |
BS2_EVENT_DEVICE_RS485_DISCONNCTED | 0x3E00 | RS485 disconnected | |
BS2_EVENT_DEVICE_INPUT_DETECTED | 0x3F00 | Input device detected | |
BS2_EVENT_DEVICE_TAMPER_ON | 0x4000 | Device or peripheral was removed | |
BS2_EVENT_DEVICE_TAMPER_OFF | 0x4100 | Device or peripheral was reconnected | |
BS2_EVENT_DEVICE_EVENT_LOG_CLEARED | 0x4200 | Log was deleted | |
BS2_EVENT_DEVICE_FIRMWARE_UPGRADED | 0x4300 | Firmware was updated | |
BS2_EVENT_DEVICE_RESOURCE_UPGRADED | 0x4400 | Resource was updated | |
BS2_EVENT_DEVICE_CONFIG_RESET | 0x4500 | System information was initialized(including network) | |
BS2_EVENT_DEVICE_DATABASE_RESET | 0x4501 | Database was initialized | |
BS2_EVENT_DEVICE_FACTORY_RESET | 0x4502 | Factory default | |
BS2_EVENT_DEVICE_CONFIG_RESET_EX | 0x4503 | System information was initialized(without network) | |
Supervised Input | BS2_EVENT_SUPERVISED_INPUT_SHORT | 0x4600 | Supervised Input (Short circuit detection) |
BS2_EVENT_SUPERVISED_INPUT_OPEN | 0x4700 | Supervised Input (Disconnection detection) | |
Device-Ex | BS2_EVENT_DEVICE_AC_FAIL | 0x4800 | AC Power failed |
BS2_EVENT_DEVICE_AC_SUCCESS | 0x4900 | AC Power succeeded | |
Door | BS2_EVENT_DOOR_UNLOCKED | 0x5000 | Door unlocked |
BS2_EVENT_DOOR_LOCKED | 0x5100 | Door locked | |
BS2_EVENT_DOOR_OPENED | 0x5200 | Door opened | |
BS2_EVENT_DOOR_CLOSED | 0x5300 | Door closed | |
BS2_EVENT_DOOR_FORCED_OPEN | 0x5400 | Door forced open | |
BS2_EVENT_DOOR_HELD_OPEN | 0x5500 | Door held open | |
BS2_EVENT_DOOR_FORCED_OPEN_ALARM | 0x5600 | Door-forced-to-open alarm has started | |
BS2_EVENT_DOOR_FORCED_OPEN_ALARM_CLEAR | 0x5700 | Door-forced-to-open alarm was released | |
BS2_EVENT_DOOR_HELD_OPEN_ALARM | 0x5800 | Door-held-open alarm has started | |
BS2_EVENT_DOOR_HELD_OPEN_ALARM_CLEAR | 0x5900 | Door-held-open alarm was released | |
BS2_EVENT_DOOR_APB_ALARM | 0x5A00 | Door-level anti-passback alarm has started | |
BS2_EVENT_DOOR_APB_ALARM_CLEAR | 0x5B00 | Door-level anti-passback alarm was released | |
Zone | BS2_EVENT_ZONE_APB_VIOLATION | 0x6000 | Zone-level anti-passback rule has been violated |
BS2_EVENT_ZONE_APB_ALARM | 0x6100 | Zone-level anti-passback alarm has started | |
BS2_EVENT_ZONE_APB_ALARM_CLEAR | 0x6200 | Zone-level anti-passback alarm was released | |
BS2_EVENT_ZONE_TIMED_APB_VIOLATION | 0x6300 | Timed anti-passback rule has been violated | |
BS2_EVENT_ZONE_TIMED_APB_ALARM | 0x6400 | Timed anti-passback alarm has started | |
BS2_EVENT_ZONE_TIMED_APB_ALARM_CLEAR | 0x6500 | Timed anti-passback alarm was released | |
BS2_EVENT_ZONE_FIRE_ALARM_INPUT | 0x6600 | Fire alarm input was detected | |
BS2_EVENT_ZONE_FIRE_ALARM | 0x6700 | Fire alarm has started | |
BS2_EVENT_ZONE_FIRE_ALARM_CLEAR | 0x6800 | Fire alarm was released | |
BS2_EVENT_ZONE_FORCED_LOCK_START | 0x6900 | Door-forced-locked schedule has started | |
BS2_EVENT_ZONE_FORCED_LOCK_END | 0x6A00 | Door-forced-locked schedule has ended | |
BS2_EVENT_ZONE_FORCED_UNLOCK_START | 0x6B00 | Door-forced-unlocked schedule has started | |
BS2_EVENT_ZONE_FORCED_UNLOCK_END | 0x6C00 | Door-forced-unlocked schedule has ended | |
BS2_EVENT_ZONE_SCHEDULED_UNLOCK_END | 0x6D00 | Scheduled unlock ended | |
BS2_EVENT_ZONE_SCHEDULED_LOCK_ALARM | 0x6E00 | Scheduled lock alarm zone start | |
BS2_EVENT_ZONE_SCHEDULED_LOCK_ALARM_CLEAR | 0x6F00 | Scheduled lock alarm zone clear |
18. param
It is used only when extra information on the device is needed. Usually, a time and attendance code, a port number of the door or input device is stored in the param argument.
When a time and attendance code is stored, refer to the following values:
Device Type | T&A Code | Mapped Key | Value |
---|---|---|---|
BioStation 2 | BS2_TNA_UNSPECIFIED | (N/A) | 0 |
BS2_TNA_KEY_1 | F1 | 1 | |
BS2_TNA_KEY_2 | F2 | 2 | |
BS2_TNA_KEY_3 | F3 | 3 | |
BS2_TNA_KEY_4 | F4 | 4 | |
BS2_TNA_KEY_5 | 1 | 5 | |
BS2_TNA_KEY_6 | 2 | 6 | |
BS2_TNA_KEY_7 | 3 | 7 | |
BS2_TNA_KEY_8 | 4 | 8 | |
BS2_TNA_KEY_9 | 5 | 9 | |
BS2_TNA_KEY_10 | 6 | 10 | |
BS2_TNA_KEY_11 | 7 | 11 | |
BS2_TNA_KEY_12 | 8 | 12 | |
BS2_TNA_KEY_13 | 9 | 13 | |
BS2_TNA_KEY_14 | Call | 14 | |
BS2_TNA_KEY_15 | 0 | 15 | |
BS2_TNA_KEY_16 | Esc | 16 |
[+ 2.6.3] Additional feature of param
Only if the event code is relevant to the user.
If you add, modify or delete users directly from the device, param is 1, 0 if done through BioStar.
For example, if param was 1 with the event BS2_EVENT_USER_ENROLL_SUCCESS, it means the user was added directly on the device.
This feature is supported from the firmware version below.
Device Type | Supported Ver. |
---|---|
BioStation 2 | V1.7.0 |
BioStation A2 | V1.6.0 |
CoreStation 40 | V1.2.0 |
BioEntry P2 | V1.2.0 |
BioStation L2 | V1.4.0 |
BioLite N2 | V1.1.0 |
BioEntry W2 | V1.3.0 |
FaceStation 2 | V1.2.0 |
19. image
Prior to SDK V2.6.0, it used the whole 1 byte and means below:
- Whether the image was included when the event occurred (true / false).
Since SDK V2.6.0, 1 byte has been changed to provide the following information by bit unit.
- Whether or not image is included.
- Whether DST is applied
Category | Bit | Parameter | Description |
---|---|---|---|
Prior to SDK 2.6.0 | 8 | image | Used in case image is included when an event occurs. |
Since SDK 2.6.0 | 1 | image | Used in case image is included when an event occurs. |
1 | isDST | Whether the current log has been applied to DST | |
1 | half | Whether DST is covered in 30-minute increments. 0 is 0 minutes, 1 is 30 minutes. | |
4 | hour | Time. 1 to 12 o'clock | |
1 | negative | 0 is +, 1 is - |
BS2EventBlob
typedef struct { uint16_t eventMask; uint32_t id; BS2EventExtInfo info; union { BS2_USER_ID userID; // valid if eventMask has BS2_EVENT_MASK_USER_ID uint8_t cardID[BS2_CARD_DATA_SIZE]; // valid if eventMask has BS2_EVENT_MASK_CARD_ID BS2_DOOR_ID doorID; // valid if eventMask has BS2_EVENT_MASK_DOOR_ID BS2_ZONE_ID zoneID; // valid if eventMask has BS2_EVENT_MASK_ZONE_ID BS2EventExtIoDevice ioDevice; // valid if eventMask has BS2_EVENT_MASK_IODEVICE }; uint8_t tnaKey; uint32_t jobCode; uint16_t imageSize; uint8_t image[BS2_EVENT_MAX_IMAGE_SIZE]; uint8_t reserved; } BS2EventBlob;
1. eventMask
Event mask value. Logs will be retrieved based on the mask value such as user, card, door, or zone.
Value | Description |
---|---|
0x0000 | None |
0x0001 | BS2EventExtInfo Structure |
0x0002 | User ID |
0x0004 | Card ID |
0x0008 | Door ID |
0x0010 | Zone ID |
0x0020 | BS2EventExtIoDevice Structure |
0x0040 | TNA Key |
0x0080 | Job Code |
0x0100 | Image |
0x0200 | Temperature |
0xFFFF | ALL |
2. id
Log record ID which automatically increases from 1 when the log is generated.
3. info
BS2EventExtInfo structure information.
4. userID
User ID related to log. When the value is 0, the log is not relevant to user.
5. cardID
Card ID related to log. When the value is 0, the log is not relevant to card.
The device records card ID only for failure auth, it returns user ID when successful auth regardless of eventMask value.
6. doorID
Door ID related to log. When the value is 0, the log is not relevant to door.
7. zoneID
Zone ID related to log. When the value is 0, the log is not relevant to zone.
8. ioDevice
Door or input device ID related to log. When the value is 0, the log is not relevant to door or input. Refer to BS2EventExtIoDevice structure.
9. tnaKey
The T&A key that has been used for the authentication. When the value is 0, the log is not relevant to T&A key.
10. jobCode
The job code that has been used for the authentication. When the value is 0, the log is not relevant to job code.
11. imageSize
Size of the image when there is an image log.
12. image
Data of the image.
13. reserved
Reserved space.
BS2EventExtInfo
typedef struct { uint32_t dateTime; uint32_t deviceID; union { ///< 2 bytes BS2_EVENT_CODE code; struct { uint8_t subCode; uint8_t mainCode; }; }; uint8_t reserved[2]; } BS2EventExtInfo;
1. dateTime
The time when the log has been generated. It means the seconds past from UTC until the current time.
2. deviceID
ID of the device that generated the log.
3. subCode
Sub code value of log types. Use if the additional information is necessary.
4. mainCode
Main code value of log types.
5. reserved
Reserved space.
BS2EventExtIoDevice
typedef struct { uint32_t ioDeviceID; uint16_t port; uint8_t value; uint8_t reserved[1]; } BS2EventExtInfo;
1. ioDeviceID
Door or input device ID related to log. When the value is 0, the log is not relevant to door or input.
2. port
Input port number.
3. value
Status of the input port.
Value | Description |
---|---|
-1 | Unknown |
0 | Open |
1 | Closed |
2 | Supervised Short |
3 | Supervised Open |
4. reserved
Reserved space.
BS2EventSmallBlob
typedef struct { uint16_t eventMask; uint32_t id; BS2EventExtInfo info; union { BS2_USER_ID userID; // valid if eventMask has BS2_EVENT_MASK_USER_ID uint8_t cardID[BS2_CARD_DATA_SIZE]; // valid if eventMask has BS2_EVENT_MASK_CARD_ID BS2_DOOR_ID doorID; // valid if eventMask has BS2_EVENT_MASK_DOOR_ID BS2_ZONE_ID zoneID; // valid if eventMask has BS2_EVENT_MASK_ZONE_ID BS2EventExtIoDevice ioDevice; // valid if eventMask has BS2_EVENT_MASK_IODEVICE }; uint8_t tnaKey; uint32_t jobCode; uint16_t imageSize; uint8_t* imageObj; // valid if eventMask has BS2_EVENT_MASK_IMAGE uint8_t reserved; } BS2EventSmallBlob;
1. eventMask
Event mask value. Logs will be retrieved based on the mask value such as user, card, door, or zone.
Value | Description |
---|---|
0x0000 | None |
0x0001 | BS2EventExtInfo Structure |
0x0002 | User ID |
0x0004 | Card ID |
0x0008 | Door ID |
0x0010 | Zone ID |
0x0020 | BS2EventExtIoDevice Structure |
0x0040 | TNA Key |
0x0080 | Job Code |
0x0100 | Image |
0x0200 | Temperature |
0xFFFF | ALL |
2. id
Log record ID which automatically increases from 1 when the log is generated.
3. info
BS2EventExtInfo structure information.
4. userID
User ID related to log. When the value is 0, the log is not relevant to user.
5. cardID
Card ID related to log. When the value is 0, the log is not relevant to card.
The device records card ID only for failure auth, it returns user ID when successful auth regardless of eventMask value.
6. doorID
Door ID related to log. When the value is 0, the log is not relevant to door.
7. zoneID
Zone ID related to log. When the value is 0, the log is not relevant to zone.
8. ioDevice
Door or input device ID related to log. When the value is 0, the log is not relevant to door or input. Refer to BS2EventExtIoDevice structure.
9. tnaKey
The T&A key that has been used for the authentication. When the value is 0, the log is not relevant to T&A key.
10. jobCode
The job code that has been used for the authentication. When the value is 0, the log is not relevant to job code.
11. imageSize
Size of the image when there is an image log.
12. imageObj
Data of the image.
13. reserved
Reserved space.
BS2EventSmallBlobEx
typedef struct { uint16_t eventMask; uint32_t id; BS2EventExtInfo info; // valid if eventMask has BS2_EVENT_MASK_INFO union { BS2_USER_ID userID; // valid if eventMask has BS2_EVENT_MASK_USER_ID uint8_t cardID[BS2_CARD_DATA_SIZE]; // valid if eventMask has BS2_EVENT_MASK_CARD_ID BS2_DOOR_ID doorID; // valid if eventMask has BS2_EVENT_MASK_DOOR_ID BS2_ZONE_ID zoneID; // valid if eventMask has BS2_EVENT_MASK_ZONE_ID BS2EventExtIoDevice ioDevice; // valid if eventMask has BS2_EVENT_MASK_IODEVICE }; uint8_t tnaKey; // valid if eventMask has BS2_EVENT_MASK_TNA_KEY uint32_t jobCode; // valid if eventMask has BS2_EVENT_MASK_JOB_CODE uint16_t imageSize; // valid if eventMask has BS2_EVENT_MASK_IMAGE uint8_t* imageObj; // valid if eventMask has BS2_EVENT_MASK_IMAGE uint8_t reserved; uint32_t temperature; // valid if eventMask has BS2_EVENT_MASK_TEMPERATURE } BS2EventSmallBlobEx;
1. eventMask
Event mask value. Logs will be retrieved based on the mask value such as user, card, door, or zone.
Value | Description |
---|---|
0x0000 | None |
0x0001 | BS2EventExtInfo Structure |
0x0002 | User ID |
0x0004 | Card ID |
0x0008 | Door ID |
0x0010 | Zone ID |
0x0020 | BS2EventExtIoDevice Structure |
0x0040 | TNA Key |
0x0080 | Job Code |
0x0100 | Image |
0x0200 | Temperature |
0xFFFF | ALL |
2. id
Log record ID which automatically increases from 1 when the log is generated.
3. info
BS2EventExtInfo structure information.
4. userID
User ID related to log. When the value is 0, the log is not relevant to user.
5. cardID
Card ID related to log. When the value is 0, the log is not relevant to card.
The device records card ID only for failure auth, it returns user ID when successful auth regardless of eventMask value.
6. doorID
Door ID related to log. When the value is 0, the log is not relevant to door.
7. zoneID
Zone ID related to log. When the value is 0, the log is not relevant to zone.
8. ioDevice
Door or input device ID related to log. When the value is 0, the log is not relevant to door or input. Refer to BS2EventExtIoDevice structure.
9. tnaKey
The T&A key that has been used for the authentication. When the value is 0, the log is not relevant to T&A key.
10. jobCode
The job code that has been used for the authentication. When the value is 0, the log is not relevant to job code.
11. imageSize
Size of the image when there is an image log.
12. image
Data of the image.
13. temperature
Temperature information is set when there's a thermal camera installed and setting to record event logs. Refer to auditTemperature
14. reserved
Reserved.