Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
en:communication_api [2019/05/27 11:53] yjjung [Communication API] |
en:communication_api [2023/02/28 14:51] (current) mwkim [Communication API] |
||
|---|---|---|---|
| Line 8: | Line 8: | ||
| * [[BS2_GetDevices]]: Gets the managed device information. | * [[BS2_GetDevices]]: Gets the managed device information. | ||
| * [[BS2_ConnectDevice]]: Connects the device using the device identifier. | * [[BS2_ConnectDevice]]: Connects the device using the device identifier. | ||
| + | * [[BS2_ConnectDeviceIPV6]]: Connects the device in IPv6 mode using the device identifier. | ||
| * [[BS2_ConnectDeviceViaIP]]: Connect devices using IP address and Port. | * [[BS2_ConnectDeviceViaIP]]: Connect devices using IP address and Port. | ||
| * [[BS2_DisconnectDevice]]: Disconnects from the device. | * [[BS2_DisconnectDevice]]: Disconnects from the device. | ||
| * [[BS2_SetKeepAliveTimeout]]: Sets the keep-alive timeout. | * [[BS2_SetKeepAliveTimeout]]: Sets the keep-alive timeout. | ||
| * [[BS2_SetNotificationListener]]: Sets the Notification listener. | * [[BS2_SetNotificationListener]]: Sets the Notification listener. | ||
| - | * [[BS2_SetServerPort]]: Set the Server Port. | + | * [[BS2_SetServerPort]]: Sets the server Port. |
| - | * [[BS2_GetServerPort]]: [+ 2.6.3] Get the Server Port. | + | * [[BS2_SetSSLServerPort]]: Sets the SSL server Port. |
| - | * [[BS2_GetSSLServerPort]]: [+ 2.6.3] Get the SSL server port. | + | * [[BS2_GetServerPort]]: [+ 2.6.3] Gets the server Port. |
| - | * [[BS2_IsConnected]]: Check device connection status. | + | * [[BS2_GetSSLServerPort]]: [+ 2.6.3] Gets the SSL server port. |
| - | * [[BS2_IsAutoConnection]]: Check auto connection status. | + | * [[BS2_IsConnected]]: Checks device connection status. |
| - | * [[BS2_SetAutoConnection]]: Set auto connection. | + | * [[BS2_IsAutoConnection]]: Checks auto connection status. |
| - | * [[BS2_GetEnableIPV4]]: [+ 2.6.3] Get IPv4 connection mode. | + | * [[BS2_SetAutoConnection]]: Sets auto connection. |
| - | * [[BS2_SetEnableIPV4]]: [+ 2.6.3] Set IPv4 connection mode. | + | * [[BS2_GetEnableIPV4]]: [+ 2.6.3] Gets IPv4 connection mode. |
| - | * [[BS2_GetEnableIPV6]]: [+ 2.6.3] Get IPv6 connection mode. | + | * [[BS2_SetEnableIPV4]]: [+ 2.6.3] Sets IPv4 connection mode. |
| - | * [[BS2_SetEnableIPV6]]: [+ 2.6.3] Set IPv6 connection mode. | + | * [[BS2_GetEnableIPV6]]: [+ 2.6.3] Gets IPv6 connection mode. |
| - | * [[BS2_SetServerPortIPV6]]: [+ 2.6.3] IP V6를 이용하여 서버모드 연결 시 연결 port를 정의합니다. | + | * [[BS2_SetEnableIPV6]]: [+ 2.6.3] Sets IPv6 connection mode. |
| - | * [[BS2_GetServerPortIPV6]]: [+ 2.6.3] IP V6를 이용하여 서버모드 연결 시 연결 port 정보를 확인합니다. | + | * [[BS2_SetServerPortIPV6]]: [+ 2.6.3] Sets server port when connecting IPv6 server mode. |
| - | * [[BS2_SetSSLServerPortIPV6]]: [+ 2.6.3] IP V6와 ssl을 이용하여 서버모드 연결 시 연결 port를 정의합니다. | + | * [[BS2_GetServerPortIPV6]]: [+ 2.6.3] Gets server port when connecting IPv6 server mode. |
| - | * [[BS2_GetSSLServerPortIPV6]]: [+ 2.6.3] IP V6와 ssl을 이용하여 서버모드 연결 시 연결 port 정보를 확인합니다. | + | * [[BS2_SetSSLServerPortIPV6]]: [+ 2.6.3] Sets server port when connecting IPv6 server mode using SSL. |
| - | * [[BS2_SetDefaultResponseTimeout]]: [+ 2.6.3] 장치와의 패킷 응답 대기시간을 설정합니다. | + | * [[BS2_GetSSLServerPortIPV6]]: [+ 2.6.3] Gets server port when connecting IPv6 server mode using SSL. |
| - | * [[BS2_GetDefaultResponseTimeout]]: [+ 2.6.3] 장치와의 패킷 응답 대시시간 정보를 확인합니다. | + | * [[BS2_SetDefaultResponseTimeout]]: [+ 2.6.3] Sets default response timeout between device and server. |
| + | * [[BS2_GetDefaultResponseTimeout]]: [+ 2.6.3] Gets default response timeout between device and server. | ||
| + | * [[BS2_GetSocketRetryCount]]: [+ 2.9.1] Gets the setting value of the number of retries for read/write failures during Non SSL communication. | ||
| + | * [[BS2_SetSocketRetryCount]]: [+ 2.9.1] Set the number of retries for read/write failures during Non SSL communication. | ||
| + | * [[BS2_GetSocketSSLRetryCount]]: [+ 2.9.1] Gets the setting value of the number of retries for read/write failures during SSL communication. | ||
| + | * [[BS2_SetSocketSSLRetryCount]]: [+ 2.9.1] Set the number of retries for read/write failures during SSL communication. | ||
| ===== Callback Function ===== | ===== Callback Function ===== | ||
| <code cpp> | <code cpp> | ||
| Line 48: | Line 55: | ||
| 5. // OnAlarmFired // \\ | 5. // OnAlarmFired // \\ | ||
| Callback function that is called when an alarm set in the Zone occurs. \\ \\ | Callback function that is called when an alarm set in the Zone occurs. \\ \\ | ||
| - | 6. // OnInputDetected // // | + | 6. // OnInputDetected // \\ |
| Callback function that is called when an input signal is generated. \\ \\ | Callback function that is called when an input signal is generated. \\ \\ | ||
| - | 7. // OnConfigChanged // | + | 7. // OnConfigChanged // \\ |
| Callback function that is called when the configuration is changed by manipulating the terminal. \\ | Callback function that is called when the configuration is changed by manipulating the terminal. \\ | ||