Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
en:log_management_api [2018/02/06 11:12] yjjung [BS2EventBlob] |
en:log_management_api [2020/02/18 11:03] yjjung [Log Management API] |
||
---|---|---|---|
Line 11: | Line 11: | ||
* [[BS2_GetLogBlob]]: Gets certain amount of logs based on the event mask. | * [[BS2_GetLogBlob]]: Gets certain amount of logs based on the event mask. | ||
* [[BS2_GetFilteredLogSinceEventId]]: Gets filtered logs. | * [[BS2_GetFilteredLogSinceEventId]]: Gets filtered logs. | ||
+ | * [[BS2_GetImageLog]] : Gets image logs using event ID. | ||
+ | * [[BS2_GetLogSmallBlob]]: [+ 2.6.4] Gets certain amount of logs based on the event mask in an efficient way. | ||
===== Callback Function ===== | ===== Callback Function ===== | ||
<code cpp> | <code cpp> | ||
Line 31: | Line 33: | ||
union { | union { | ||
char userID[BS2_USER_ID_SIZE]; | char userID[BS2_USER_ID_SIZE]; | ||
- | uint32_t ioDeviceID; | + | uint32_t uid; |
+ | uint32_t doorID; | ||
+ | uint32_t liftID; | ||
+ | uint32_t zoneID; | ||
+ | struct { | ||
+ | uint32_t ioDeviceID; | ||
+ | uint16_t port; | ||
+ | int8_t value; | ||
+ | uint8_t reserved[25]; | ||
+ | }; | ||
+ | struct { | ||
+ | uint32_t zoneID; | ||
+ | uint32_t doorID; | ||
+ | uint32_t ioDeviceID; | ||
+ | uint16_t port; | ||
+ | uint8_t reserved[18]; | ||
+ | } alarm; | ||
+ | struct { | ||
+ | uint32_t zoneID; | ||
+ | uint32_t doorID[4]; | ||
+ | uint8_t reserved[12]; | ||
+ | } interlock; | ||
}; | }; | ||
union { | union { | ||
uint16_t code; | uint16_t code; | ||
struct { | struct { | ||
- | uint8_t mainCode; | ||
uint8_t subCode; | uint8_t subCode; | ||
+ | uint8_t mainCode; | ||
}; | }; | ||
}; | }; | ||
uint8_t param; | uint8_t param; | ||
- | uint8_t image; | + | #ifdef LESS_THAN_SDK_2_6_0 |
+ | BS2_BOOL image; // Deprecated in V2.6.0 | ||
+ | #else | ||
+ | uint8_t image: 1; // Support image and DST by bit division | ||
+ | uint8_t isDST: 1; | ||
+ | uint8_t half: 1; | ||
+ | uint8_t hour: 4; | ||
+ | uint8_t negative: 1; | ||
+ | #endif | ||
} BS2Event; | } BS2Event; | ||
</code> | </code> | ||
Line 54: | Line 85: | ||
**4. //userID//** \\ | **4. //userID//** \\ | ||
User ID related to log. When the value is 0, the log is not relevant to user. \\ \\ | User ID related to log. When the value is 0, the log is not relevant to user. \\ \\ | ||
- | **5. //ioDeviceID//** \\ | + | **5. //uid//** \\ |
+ | You can refer to doorID regarding door log, zoneID regarding zone log. | ||
+ | If you do not know exactly then you can refer to uid. \\ | ||
+ | Since uid, doorID, liftID, zoneID are declared as union, basically it means information such as unordered list. \\ \\ | ||
+ | **6. //doorID//** \\ | ||
+ | ID of the door that generated the log. \\ \\ | ||
+ | **7. //liftID//** \\ | ||
+ | ID of the lift that generated the log. \\ \\ | ||
+ | **8. //zoneID//** \\ | ||
+ | ID of the zone that generated the log. \\ \\ | ||
+ | **9. //ioDeviceID//** \\ | ||
Door or Input device ID. When the value is 0, the log is not relevant to Door or Input device. \\ \\ | Door or Input device ID. When the value is 0, the log is not relevant to Door or Input device. \\ \\ | ||
- | **6. //mainCode//** \\ | + | **10. //port//** \\ |
- | Main code value of log types. \\ | + | Port for ioDeviceID. \\ \\ |
- | ^Category ^Event code ^Value ^Description ^ | + | **11. //value//** \\ |
- | |Auth |BS2_EVENT_VERIFY_SUCCESS |0x10 |1:1 authentication success | | + | Port value for ioDeviceID and means below. \\ |
- | |::: |BS2_EVENT_VERIFY_FAIL |0x11 |1:1 authentication fail | | + | BS2_PORT_VALUE_UNKNOWN : -1 \\ |
- | |::: |BS2_EVENT_VERIFY_DURESS |0x12 |1:1 duress authentication success | | + | BS2_PORT_VALUE_OPEN : 0 \\ |
- | |::: |BS2_EVENT_IDENTIFY_SUCCESS |0x13 |1:N authentication success | | + | BS2_PORT_VALUE_CLOSED : 1 \\ |
- | |::: |BS2_EVENT_IDENTIFY_FAIL |0x14 |1:N authentication fail | | + | BS2_PORT_VALUE_SUPERVISED_SHORT : 2 \\ |
- | |::: |BS2_EVENT_IDENTIFY_DURESS |0x15 |1:N duress authentication success | | + | BS2_PORT_VALUE_SUPERVISED_OPEN : 3 \\ \\ |
- | |::: |BS2_EVENT_DUAL_AUTH_SUCCESS |0x16 |Dual authentication success | | + | **12. //alarm.zoneID//** \\ |
- | |::: |BS2_EVENT_DUAL_AUTH_FAIL |0x17 |Dual authentication fail | | + | Zone ID that makes intrusion alarm zone alarms. \\ \\ |
- | |::: |BS2_EVENT_AUTH_FAILED |0x18 |Attempted to authenticate with the non-registered credential| | + | **13. //alarm.doorID//** \\ |
- | |::: |BS2_EVENT_ACCESS_DENIED |0x19 |Invalid user attempted to authenticate or user violated the APB rule| | + | Door ID that makes intrusion alarm zone alarms. \\ \\ |
- | |User |BS2_EVENT_USER_ENROLL_SUCCESS |0x20 |User enroll success | | + | **14. //interlock.zoneID//** \\ |
- | |::: |BS2_EVENT_USER_ENROLL_FAIL |0x21 |User enroll fail | | + | Zone ID that makes interlock zone alarms. \\ \\ |
- | |::: |BS2_EVENT_USER_UPDATE_SUCCESS |0x22 |User update success | | + | **15. //interlock.doorID//** \\ |
- | |::: |BS2_EVENT_USER_UPDATE_FAIL |0x23 |User update fail | | + | Door ID that makes interlock zone alarms. \\ \\ |
- | |::: |BS2_EVENT_USER_DELETE_SUCCESS |0x24 |User delete success | | + | **16. //subCode//** \\ |
- | |::: |BS2_EVENT_USER_DELETE_FAIL |0x25 |User delete fail | | + | |
- | |::: |BS2_EVENT_USER_DELETE_ALL_SUCCESS |0x26 |Delete all user success | | + | |
- | |::: |BS2_EVENT_USER_ISSUE_AOC_SUCCESS |0x26 |Authentication success with access card | | + | |
- | |Device |BS2_EVENT_DEVICE_SYSTEM_RESET |0x30 |System reset | | + | |
- | |::: |BS2_EVENT_DEVICE_SYSTEM_STARTED |0x31 |System started | | + | |
- | |::: |BS2_EVENT_DEVICE_TIME_SET |0x32 |System time set | | + | |
- | |::: |BS2_EVENT_DEVICE_LINK_CONNECTED |0x33 |LAN cable connected | | + | |
- | |::: |BS2_EVENT_DEVICE_LINK_DISCONNETED |0x34 |LAN cable disconnected | | + | |
- | |::: |BS2_EVENT_DEVICE_DHCP_SUCCESS |0x35 |IP address allocated by DHCP | | + | |
- | |::: |BS2_EVENT_DEVICE_ADMIN_MENU |0x36 |Open administrator menu | | + | |
- | |::: |BS2_EVENT_DEVICE_UI_LOCKED |0x37 |Screen locked | | + | |
- | |::: |BS2_EVENT_DEVICE_UI_UNLOCKED |0x38 |Screen unlocked | | + | |
- | |::: |BS2_EVENT_DEVICE_COMM_LOCKED |0x39 |RS485 communication locked | | + | |
- | |::: |BS2_EVENT_DEVICE_COMM_UNLOCKED |0x3A |RS485 communication unlocked | | + | |
- | |::: |BS2_EVENT_DEVICE_TCP_CONNECTED |0x3B |TCP connected | | + | |
- | |::: |BS2_EVENT_DEVICE_TCP_DISCONNECTED |0x3C |TCP disconnected | | + | |
- | |::: |BS2_EVENT_DEVICE_RS485_CONNECTED |0x3D |RS485 connected | | + | |
- | |::: |BS2_EVENT_DEVICE_RS485_DISCONNCTED |0x3E |RS485 disconnected | | + | |
- | |::: |BS2_EVENT_DEVICE_INPUT_DETECTED |0x3F |Input device detected | | + | |
- | |::: |BS2_EVENT_DEVICE_TAMPER_ON |0x40 |Device or peripheral was removed| | + | |
- | |::: |BS2_EVENT_DEVICE_TAMPER_OFF |0x41 |Device or peripheral was reconnected| | + | |
- | |::: |BS2_EVENT_DEVICE_EVENT_LOG_CLEARED |0x42 |Log was deleted| | + | |
- | |::: |BS2_EVENT_DEVICE_FIRMWARE_UPGRADED |0x43 |Firmware was updated| | + | |
- | |::: |BS2_EVENT_DEVICE_RESOURCE_UPGRADED |0x44 |Resource was updated| | + | |
- | |::: |BS2_EVENT_DEVICE_CONFIG_RESET |0x45 |System information was initialized| | + | |
- | |Door |BS2_EVENT_DOOR_UNLOCKED |0x50 |Door unlocked | | + | |
- | |::: |BS2_EVENT_DOOR_LOCKED |0x51 |Door locked | | + | |
- | |::: |BS2_EVENT_DOOR_OPENED |0x52 |Door opened | | + | |
- | |::: |BS2_EVENT_DOOR_CLOSED |0x53 |Door closed | | + | |
- | |::: |BS2_EVENT_DOOR_FORCED_OPEN |0x54 |Door forced open | | + | |
- | |::: |BS2_EVENT_DOOR_HELD_OPEN |0x55 |Door held open | | + | |
- | |::: |BS2_EVENT_DOOR_FORCED_OPEN_ALARM |0x56 |Door-forced-to-open alarm has started| | + | |
- | |::: |BS2_EVENT_DOOR_FORCED_OPEN_ALARM_CLEAR |0x57 |Door-forced-to-open alarm was released| | + | |
- | |::: |BS2_EVENT_DOOR_HELD_OPEN_ALARM |0x58 |Door-held-open alarm has started| | + | |
- | |::: |BS2_EVENT_DOOR_HELD_OPEN_ALARM_CLEAR |0x59 |Door-held-open alarm was released| | + | |
- | |::: |BS2_EVENT_DOOR_APB_ALARM |0x5A |Door-level anti-passback alarm has started| | + | |
- | |::: |BS2_EVENT_DOOR_APB_ALARM_CLEAR |0x5B |Door-level anti-passback alarm was released| | + | |
- | |Zone |BS2_EVENT_ZONE_APB_VIOLATION |0x60 |Zone-level anti-passback rule has been violated| | + | |
- | |::: |BS2_EVENT_ZONE_APB_ALARM |0x61 |Zone-level anti-passback alarm has started| | + | |
- | |::: |BS2_EVENT_ZONE_APB_ALARM_CLEAR |0x62 |Zone-level anti-passback alarm was released| | + | |
- | |::: |BS2_EVENT_ZONE_TIMED_APB_VIOLATION |0x63 |Timed anti-passback rule has been violated| | + | |
- | |::: |BS2_EVENT_ZONE_TIMED_APB_ALARM |0x64 |Timed anti-passback alarm has started| | + | |
- | |::: |BS2_EVENT_ZONE_TIMED_APB_ALARM_CLEAR |0x65 |Timed anti-passback alarm was released| | + | |
- | |::: |BS2_EVENT_ZONE_FIRE_ALARM_INPUT |0x66 |Fire alarm input was detected| | + | |
- | |::: |BS2_EVENT_ZONE_FIRE_ALARM |0x67 |Fire alarm has started| | + | |
- | |::: |BS2_EVENT_ZONE_FIRE_ALARM_CLEAR |0x68 |Fire alarm was released| | + | |
- | |::: |BS2_EVENT_ZONE_FORCED_LOCK_START |0x69 |Door-forced-locked schedule has started| | + | |
- | |::: |BS2_EVENT_ZONE_FORCED_LOCK_END |0x6A |Door-forced-locked schedule has ended| | + | |
- | |::: |BS2_EVENT_ZONE_FORCED_UNLOCK_START |0x6B |Door-forced-unlocked schedule has started| | + | |
- | |::: |BS2_EVENT_ZONE_FORCED_UNLOCK_END |0x6C |Door-forced-unlocked schedule has ended| | + | |
- | **7. //subCode//** \\ | + | |
Sub code value of log types. Use if the additional information is necessary. \\ | Sub code value of log types. Use if the additional information is necessary. \\ | ||
^Category ^Event code ^Value ^Description ^ | ^Category ^Event code ^Value ^Description ^ | ||
Line 132: | Line 122: | ||
|::: |BS2_SUB_EVENT_VERIFY_ID_FACE |0x04 |ID and face verification success | | |::: |BS2_SUB_EVENT_VERIFY_ID_FACE |0x04 |ID and face verification success | | ||
|::: |BS2_SUB_EVENT_VERIFY_ID_FACE_PIN |0x05 |ID, face, and PIN verification success | | |::: |BS2_SUB_EVENT_VERIFY_ID_FACE_PIN |0x05 |ID, face, and PIN verification success | | ||
- | |::: |BS2_SUB_EVENT_VERIFY_CARD |0x06 |Smart card verification success | | + | |::: |BS2_SUB_EVENT_VERIFY_CARD |0x06 |Card verification success | |
- | |::: |BS2_SUB_EVENT_VERIFY_CARD_PIN |0x07 |Smart card and PIN verification success | | + | |::: |BS2_SUB_EVENT_VERIFY_CARD_PIN |0x07 |Card and PIN verification success | |
- | |::: |BS2_SUB_EVENT_VERIFY_CARD_FINGER |0x08 |Smart card and fingerprint verification success | | + | |::: |BS2_SUB_EVENT_VERIFY_CARD_FINGER |0x08 |Card and fingerprint verification success | |
- | |::: |BS2_SUB_EVENT_VERIFY_CARD_FINGER_PIN |0x09 |Smart card, fingerprint, and PIN verification success | | + | |::: |BS2_SUB_EVENT_VERIFY_CARD_FINGER_PIN |0x09 |Card, fingerprint, and PIN verification success | |
- | |::: |BS2_SUB_EVENT_VERIFY_CARD_FACE |0x0A |Smart card and face verification success | | + | |::: |BS2_SUB_EVENT_VERIFY_CARD_FACE |0x0A |Card and face verification success | |
- | |::: |BS2_SUB_EVENT_VERIFY_CARD_FACE_PIN |0x0B |Smart card, PIN, and face verification success | | + | |::: |BS2_SUB_EVENT_VERIFY_CARD_FACE_PIN |0x0B |Card, PIN, and face verification success | |
|::: |BS2_SUB_EVENT_VERIFY_AOC |0x0C |AOC card verification success | | |::: |BS2_SUB_EVENT_VERIFY_AOC |0x0C |AOC card verification success | | ||
|::: |BS2_SUB_EVENT_VERIFY_AOC_PIN |0x0D |AOC card and PIN verification success | | |::: |BS2_SUB_EVENT_VERIFY_AOC_PIN |0x0D |AOC card and PIN verification success | | ||
Line 149: | Line 139: | ||
|::: |BS2_SUB_EVENT_DUAL_AUTH_FAIL_ACCESS_GROUP |0x02 |Attempted the dual authentication with invalid user| | |::: |BS2_SUB_EVENT_DUAL_AUTH_FAIL_ACCESS_GROUP |0x02 |Attempted the dual authentication with invalid user| | ||
|Credential |BS2_SUB_EVENT_CREDENTIAL_ID |0x01 |Invalid user ID| | |Credential |BS2_SUB_EVENT_CREDENTIAL_ID |0x01 |Invalid user ID| | ||
- | |::: |BS2_SUB_EVENT_CREDENTIAL_CARD |0x02 |Invalid Smart card | | + | |::: |BS2_SUB_EVENT_CREDENTIAL_CARD |0x02 |Invalid card | |
|::: |BS2_SUB_EVENT_CREDENTIAL_PIN |0x03 |Invalid PIN | | |::: |BS2_SUB_EVENT_CREDENTIAL_PIN |0x03 |Invalid PIN | | ||
|::: |BS2_SUB_EVENT_CREDENTIAL_FINGER |0x04 |Invalid fingerprint | | |::: |BS2_SUB_EVENT_CREDENTIAL_FINGER |0x04 |Invalid fingerprint | | ||
Line 167: | Line 157: | ||
|APB |BS2_SUB_EVENT_ZONE_HARD_APB |0x01 |Hard APB zone | | |APB |BS2_SUB_EVENT_ZONE_HARD_APB |0x01 |Hard APB zone | | ||
|::: |BS2_SUB_EVENT_ZONE_SOFT_APB |0x02 |Soft APB zone | | |::: |BS2_SUB_EVENT_ZONE_SOFT_APB |0x02 |Soft APB zone | | ||
- | **8. //param//** \\ | + | |
+ | **17. //mainCode//** \\ | ||
+ | Main code value of log types. \\ | ||
+ | ^Category ^Event code ^Value ^Description ^ | ||
+ | |Auth |BS2_EVENT_VERIFY_SUCCESS |0x1000 |1:1 authentication success | | ||
+ | |::: |BS2_EVENT_VERIFY_FAIL |0x1100 |1:1 authentication fail | | ||
+ | |::: |BS2_EVENT_VERIFY_DURESS |0x1200 |1:1 duress authentication success | | ||
+ | |::: |BS2_EVENT_IDENTIFY_SUCCESS |0x1300 |1:N authentication success | | ||
+ | |::: |BS2_EVENT_IDENTIFY_FAIL |0x1400 |1:N authentication fail | | ||
+ | |::: |BS2_EVENT_IDENTIFY_DURESS |0x1500 |1:N duress authentication success | | ||
+ | |::: |BS2_EVENT_DUAL_AUTH_SUCCESS |0x1600 |Dual authentication success | | ||
+ | |::: |BS2_EVENT_DUAL_AUTH_FAIL |0x1700 |Dual authentication fail | | ||
+ | |::: |BS2_EVENT_AUTH_FAILED |0x1800 |Attempted to authenticate with the non-registered credential| | ||
+ | |::: |BS2_EVENT_ACCESS_DENIED |0x1900 |Invalid user attempted to authenticate or user violated the APB rule| | ||
+ | |::: |BS2_EVENT_FAKE_FINGER_DETECTED |0x1A00 |Fake fingerprint detection | | ||
+ | |User |BS2_EVENT_USER_ENROLL_SUCCESS |0x2000 |User enroll success | | ||
+ | |::: |BS2_EVENT_USER_ENROLL_FAIL |0x2100 |User enroll fail | | ||
+ | |::: |BS2_EVENT_USER_UPDATE_SUCCESS |0x2200 |User update success | | ||
+ | |::: |BS2_EVENT_USER_UPDATE_FAIL |0x2300 |User update fail | | ||
+ | |::: |BS2_EVENT_USER_DELETE_SUCCESS |0x2400 |User delete success | | ||
+ | |::: |BS2_EVENT_USER_DELETE_FAIL |0x2500 |User delete fail | | ||
+ | |::: |BS2_EVENT_USER_DELETE_ALL_SUCCESS |0x2600 |Delete all user success | | ||
+ | |::: |BS2_EVENT_USER_ISSUE_AOC_SUCCESS |0x2700 |Authentication success with access card | | ||
+ | |::: |BS2_EVENT_USER_DUPLICATE_CREDENTIAL |0x2800 |Duplicated credential(Card/Fingerprint/Face) detection| | ||
+ | |Device |BS2_EVENT_DEVICE_SYSTEM_RESET |0x3000 |System reset | | ||
+ | |::: |BS2_EVENT_DEVICE_SYSTEM_STARTED |0x3100 |System started | | ||
+ | |::: |BS2_EVENT_DEVICE_TIME_SET |0x3200 |System time set | | ||
+ | |::: |BS2_EVENT_DEVICE_TIMEZONE_SET |0x3201 |Time zone chagned | | ||
+ | |::: |BS2_EVENT_DEVICE_DST_SET |0x3202 |DST setting changed | | ||
+ | |::: |BS2_EVENT_DEVICE_LINK_CONNECTED |0x3300 |LAN cable connected | | ||
+ | |::: |BS2_EVENT_DEVICE_LINK_DISCONNETED |0x3400 |LAN cable disconnected | | ||
+ | |::: |BS2_EVENT_DEVICE_DHCP_SUCCESS |0x3500 |IP address allocated by DHCP | | ||
+ | |::: |BS2_EVENT_DEVICE_ADMIN_MENU |0x3600 |Open administrator menu | | ||
+ | |::: |BS2_EVENT_DEVICE_UI_LOCKED |0x3700 |Screen locked | | ||
+ | |::: |BS2_EVENT_DEVICE_UI_UNLOCKED |0x3800 |Screen unlocked | | ||
+ | |::: |BS2_EVENT_DEVICE_COMM_LOCKED |0x3900 |RS485 communication locked | | ||
+ | |::: |BS2_EVENT_DEVICE_COMM_UNLOCKED |0x3A00 |RS485 communication unlocked | | ||
+ | |::: |BS2_EVENT_DEVICE_TCP_CONNECTED |0x3B00 |TCP connected | | ||
+ | |::: |BS2_EVENT_DEVICE_TCP_DISCONNECTED |0x3C00 |TCP disconnected | | ||
+ | |::: |BS2_EVENT_DEVICE_RS485_CONNECTED |0x3D00 |RS485 connected | | ||
+ | |::: |BS2_EVENT_DEVICE_RS485_DISCONNCTED |0x3E00 |RS485 disconnected | | ||
+ | |::: |BS2_EVENT_DEVICE_INPUT_DETECTED |0x3F00 |Input device detected | | ||
+ | |::: |BS2_EVENT_DEVICE_TAMPER_ON |0x4000 |Device or peripheral was removed| | ||
+ | |::: |BS2_EVENT_DEVICE_TAMPER_OFF |0x4100 |Device or peripheral was reconnected| | ||
+ | |::: |BS2_EVENT_DEVICE_EVENT_LOG_CLEARED |0x4200 |Log was deleted| | ||
+ | |::: |BS2_EVENT_DEVICE_FIRMWARE_UPGRADED |0x4300 |Firmware was updated| | ||
+ | |::: |BS2_EVENT_DEVICE_RESOURCE_UPGRADED |0x4400 |Resource was updated| | ||
+ | |::: |BS2_EVENT_DEVICE_CONFIG_RESET |0x4500 |System information was initialized(including network)| | ||
+ | |::: |BS2_EVENT_DEVICE_DATABASE_RESET |0x4501 |Database was initialized | | ||
+ | |::: |BS2_EVENT_DEVICE_FACTORY_RESET |0x4502 |Factory default | | ||
+ | |::: |BS2_EVENT_DEVICE_CONFIG_RESET_EX |0x4503 |System information was initialized(without network) | | ||
+ | |Supervised Input |BS2_EVENT_SUPERVISED_INPUT_SHORT |0x4600 |Supervised Input (Short circuit detection) | | ||
+ | |::: |BS2_EVENT_SUPERVISED_INPUT_OPEN |0x4700 |Supervised Input (Disconnection detection) | | ||
+ | |Device-Ex |BS2_EVENT_DEVICE_AC_FAIL |0x4800 |AC Power failed | | ||
+ | |::: |BS2_EVENT_DEVICE_AC_SUCCESS |0x4900 |AC Power succeeded | | ||
+ | |Door |BS2_EVENT_DOOR_UNLOCKED |0x5000 |Door unlocked | | ||
+ | |::: |BS2_EVENT_DOOR_LOCKED |0x5100 |Door locked | | ||
+ | |::: |BS2_EVENT_DOOR_OPENED |0x5200 |Door opened | | ||
+ | |::: |BS2_EVENT_DOOR_CLOSED |0x5300 |Door closed | | ||
+ | |::: |BS2_EVENT_DOOR_FORCED_OPEN |0x5400 |Door forced open | | ||
+ | |::: |BS2_EVENT_DOOR_HELD_OPEN |0x5500 |Door held open | | ||
+ | |::: |BS2_EVENT_DOOR_FORCED_OPEN_ALARM |0x5600 |Door-forced-to-open alarm has started| | ||
+ | |::: |BS2_EVENT_DOOR_FORCED_OPEN_ALARM_CLEAR |0x5700 |Door-forced-to-open alarm was released| | ||
+ | |::: |BS2_EVENT_DOOR_HELD_OPEN_ALARM |0x5800 |Door-held-open alarm has started| | ||
+ | |::: |BS2_EVENT_DOOR_HELD_OPEN_ALARM_CLEAR |0x5900 |Door-held-open alarm was released| | ||
+ | |::: |BS2_EVENT_DOOR_APB_ALARM |0x5A00 |Door-level anti-passback alarm has started| | ||
+ | |::: |BS2_EVENT_DOOR_APB_ALARM_CLEAR |0x5B00 |Door-level anti-passback alarm was released| | ||
+ | |Zone |BS2_EVENT_ZONE_APB_VIOLATION |0x6000 |Zone-level anti-passback rule has been violated| | ||
+ | |::: |BS2_EVENT_ZONE_APB_ALARM |0x6100 |Zone-level anti-passback alarm has started| | ||
+ | |::: |BS2_EVENT_ZONE_APB_ALARM_CLEAR |0x6200 |Zone-level anti-passback alarm was released| | ||
+ | |::: |BS2_EVENT_ZONE_TIMED_APB_VIOLATION |0x6300 |Timed anti-passback rule has been violated| | ||
+ | |::: |BS2_EVENT_ZONE_TIMED_APB_ALARM |0x6400 |Timed anti-passback alarm has started| | ||
+ | |::: |BS2_EVENT_ZONE_TIMED_APB_ALARM_CLEAR |0x6500 |Timed anti-passback alarm was released| | ||
+ | |::: |BS2_EVENT_ZONE_FIRE_ALARM_INPUT |0x6600 |Fire alarm input was detected| | ||
+ | |::: |BS2_EVENT_ZONE_FIRE_ALARM |0x6700 |Fire alarm has started| | ||
+ | |::: |BS2_EVENT_ZONE_FIRE_ALARM_CLEAR |0x6800 |Fire alarm was released| | ||
+ | |::: |BS2_EVENT_ZONE_FORCED_LOCK_START |0x6900 |Door-forced-locked schedule has started| | ||
+ | |::: |BS2_EVENT_ZONE_FORCED_LOCK_END |0x6A00 |Door-forced-locked schedule has ended| | ||
+ | |::: |BS2_EVENT_ZONE_FORCED_UNLOCK_START |0x6B00 |Door-forced-unlocked schedule has started| | ||
+ | |::: |BS2_EVENT_ZONE_FORCED_UNLOCK_END |0x6C00 |Door-forced-unlocked schedule has ended| | ||
+ | |::: |BS2_EVENT_ZONE_SCHEDULED_UNLOCK_END |0x6D00 |Scheduled unlock ended | | ||
+ | |::: |BS2_EVENT_ZONE_SCHEDULED_LOCK_ALARM |0x6E00 |Scheduled lock alarm zone start | | ||
+ | |::: |BS2_EVENT_ZONE_SCHEDULED_LOCK_ALARM_CLEAR |0x6F00 |Scheduled lock alarm zone clear | | ||
+ | |||
+ | **18. //param//** \\ | ||
It is used only when extra information on the device is needed. Usually, a time and attendance code, a port number of the door or input device is stored in the //param// argument. | It is used only when extra information on the device is needed. Usually, a time and attendance code, a port number of the door or input device is stored in the //param// argument. | ||
When a time and attendance code is stored, refer to the following values: | When a time and attendance code is stored, refer to the following values: | ||
Line 190: | Line 264: | ||
|:::|BS2_TNA_KEY_16|Esc|16| | |:::|BS2_TNA_KEY_16|Esc|16| | ||
</WRAP> | </WRAP> | ||
- | **9. //image//** \\ | + | \\ |
- | It is used when the event includes image information. | + | **[+ 2.6.3] Additional feature of param** \\ |
+ | Only if the event code is relevant to the user. \\ | ||
+ | If you add, modify or delete users directly from the device, param is 1, 0 if done through BioStar. \\ | ||
+ | For example, if param was 1 with the event BS2_EVENT_USER_ENROLL_SUCCESS, it means the user was added directly on the device. \\ | ||
+ | This feature is supported from the firmware version below. | ||
+ | <WRAP group 60%> | ||
+ | ^Device Type ^Supported Ver. ^ | ||
+ | |BioStation 2 |V1.7.0 | | ||
+ | |BioStation A2 |V1.6.0 | | ||
+ | |CoreStation 40 |V1.2.0 | | ||
+ | |BioEntry P2 |V1.2.0 | | ||
+ | |BioStation L2 |V1.4.0 | | ||
+ | |BioLite N2 |V1.1.0 | | ||
+ | |BioEntry W2 |V1.3.0 | | ||
+ | |FaceStation 2 |V1.2.0| | ||
+ | </WRAP> | ||
+ | \\ \\ | ||
+ | |||
+ | **19. //image//** \\ | ||
+ | Prior to SDK V2.6.0, it used the whole 1 byte and means below: \\ | ||
+ | - Whether the image was included when the event occurred (true / false). \\ \\ | ||
+ | Since SDK V2.6.0, 1 byte has been changed to provide the following information by bit unit. \\ | ||
+ | - Whether or not image is included. | ||
+ | - Whether DST is applied | ||
+ | |||
+ | ^Category ^Bit ^Parameter ^Description ^ | ||
+ | |Prior to SDK 2.6.0 |8 |image | Used in case image is included when an event occurs. | | ||
+ | |Since SDK 2.6.0 |1 |image |Used in case image is included when an event occurs. | | ||
+ | |::: |1 |isDST |Whether the current log has been applied to DST | | ||
+ | |::: |1 |half |Whether DST is covered in 30-minute increments. 0 is 0 minutes, 1 is 30 minutes. | | ||
+ | |::: |4 |hour |Time. 1 to 12 o'clock | | ||
+ | |::: |1 |negative |0 is +, 1 is - | | ||
==== BS2EventBlob==== | ==== BS2EventBlob==== |