Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
|
en:log_management_api [2021/08/05 15:01] peter |
en:log_management_api [2024/02/16 12:16] mwkim [BS2Event] |
||
|---|---|---|---|
| Line 74: | Line 74: | ||
| uint8_t reserved[12]; | uint8_t reserved[12]; | ||
| } interlock; | } interlock; | ||
| + | struct { | ||
| + | uint16_t relayPort; | ||
| + | uint16_t inputPort; | ||
| + | uint8_t reserved[28]; | ||
| + | } relayAction; | ||
| struct { | struct { | ||
| - | uint16_t relayPort; | + | BS2_DEVICE_ID deviceId; |
| - | uint16_t inputPort; | + | uint8_t data[28]; |
| - | uint8_t reserved[28]; | + | } osdpStandard; |
| - | } relayAction; | + | |
| }; | }; | ||
| union { | union { | ||
| Line 91: | Line 95: | ||
| BS2_BOOL image; // Deprecated in V2.6.0 | BS2_BOOL image; // Deprecated in V2.6.0 | ||
| #else | #else | ||
| - | uint8_t image: 1; // Support image and DST by bit division | + | uint8_t image: 1; // Supports image and DST by splitting bit unit |
| uint8_t isDST: 1; | uint8_t isDST: 1; | ||
| uint8_t half: 1; | uint8_t half: 1; | ||
| Line 140: | Line 144: | ||
| **16. //relayAction.relayPort//** \\ | **16. //relayAction.relayPort//** \\ | ||
| Relay port identifier when IM-120 RelayAction takes place. \\ \\ | Relay port identifier when IM-120 RelayAction takes place. \\ \\ | ||
| - | **17. //relayAction.inputPort// \\ | + | **17. //relayAction.inputPort//** \\ |
| Relay port identifier when IM-120 RelayAction takes place. \\ \\ | Relay port identifier when IM-120 RelayAction takes place. \\ \\ | ||
| - | 18. //subCode// \\ | + | **18. //osdpStandard.deviceId//** \\ |
| + | Identifier of the OSDP standard device. \\ \\ | ||
| + | **19. //osdpStandard.data//** \\ | ||
| + | This is notification structure information with a total size of 28 bytes generated from OSDP standard devices. \\ | ||
| + | For detailed information about the structure, please refer to [[slave_control_api#BS2OsdpStandardDeviceNotify|BS2OsdpStandardDeviceNotify]]. \\ \\ | ||
| + | **20. //subCode//** \\ | ||
| Sub code value of log types. Use if the additional information is necessary. \\ | Sub code value of log types. Use if the additional information is necessary. \\ | ||
| - | ^Category ^Event code ^Value ^Description ^ | + | ^Category ^Event code ^Value ^Description ^ |
| |Verify |BS2_SUB_EVENT_VERIFY_ID_PIN |0x01 |ID and PIN verification success | | |Verify |BS2_SUB_EVENT_VERIFY_ID_PIN |0x01 |ID and PIN verification success | | ||
| |::: |BS2_SUB_EVENT_VERIFY_ID_FINGER |0x02 |ID and fingerprint verification success | | |::: |BS2_SUB_EVENT_VERIFY_ID_FINGER |0x02 |ID and fingerprint verification success | | ||
| Line 194: | Line 203: | ||
| |APB |BS2_SUB_EVENT_ZONE_HARD_APB |0x01 |Hard APB zone | | |APB |BS2_SUB_EVENT_ZONE_HARD_APB |0x01 |Hard APB zone | | ||
| |::: |BS2_SUB_EVENT_ZONE_SOFT_APB |0x02 |Soft APB zone | | |::: |BS2_SUB_EVENT_ZONE_SOFT_APB |0x02 |Soft APB zone | | ||
| - | + | **21. //mainCode//** \\ | |
| - | **19. //mainCode//** \\ | + | |
| Main code value of log types. \\ | Main code value of log types. \\ | ||
| ^Category ^Event code ^Value ^Description ^ | ^Category ^Event code ^Value ^Description ^ | ||
| Line 283: | Line 291: | ||
| - | **20.//param//** \\ | + | **22.//param//** \\ |
| It is used only when extra information on the device is needed. Usually, a time and attendance code, a port number of the door or input device is stored in the //param// argument. | It is used only when extra information on the device is needed. Usually, a time and attendance code, a port number of the door or input device is stored in the //param// argument. | ||
| When a time and attendance code is stored, refer to the following values: | When a time and attendance code is stored, refer to the following values: | ||
| Line 325: | Line 333: | ||
| \\ \\ | \\ \\ | ||
| - | **21. //image//** \\ | + | **23. //image//** \\ |
| Prior to SDK V2.6.0, it used the whole 1 byte and means below: \\ | Prior to SDK V2.6.0, it used the whole 1 byte and means below: \\ | ||
| - Whether the image was included when the event occurred (true / false). \\ \\ | - Whether the image was included when the event occurred (true / false). \\ \\ | ||