Differences
This shows you the differences between two versions of the page.
|
en:how_to_enable_user_group_synchronization_in_active_directory [2019/10/11 11:42] yjjung created |
en:how_to_enable_user_group_synchronization_in_active_directory [2022/12/28 19:00] (current) phit |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| + | |||
| + | |||
| ===== How to enable user group synchronization in Active Directory ===== | ===== How to enable user group synchronization in Active Directory ===== | ||
| - | ---- | ||
| - | Active Directory is supported starting with BioStar 2.7.5. However, the initial Active Directory feature was inconvenience because it wasn't able to selectively synchronize user information. Beginning with BioStar 2.7.8, the 'User group' section has been added to Active Directory to enable selectively synchronization of user information. | ||
| - | If you go to Setting-Active Directory, you can set up Active Directory setting with the screen below. Red square area 'User group' is newly added since 2.7.8. | + | ---- |
| - | + | ||
| - | {{:en:active_directory_01.png?nolink&1100|}}\\ | + | Active Directory function is supported starting with BioStar 2 Version 2.7.5. |
| + | |||
| + | Furthermore, with BioStar 2 Version 2.7.8, unlike previous versions of BioStar 2 Version 2.7.8, \\ | ||
| + | users can now selectively synchronize user information through the ‘User Group’ section. \\ | ||
| + | |||
| + | |||
| + | |||
| + | Go to Setting → Active Directory, you can set up the Active Directory setting with the screen below.\\ | ||
| + | |||
| + | Red square area 'User group' is newly added from BioStar 2 Version 2.7.8. | ||
| + | |||
| + | | ||
| + | |||
| + | {{:en:active_directory_01.png?nolink&1100|}}\\ | ||
| + | |||
| + | |||
| + | |||
| + | The initial value is 'Inactive', which synchronizes all users.\\ \\ | ||
| + | |||
| + | |||
| + | |||
| + | Once you move the bar to 'Active', now BioStar 2 will synchronize users according to the 'User Group Base DN' and 'User Group' setting. \\ | ||
| + | |||
| + | |||
| + | |||
| + | {{:en:active_directory_02.png?nolink&1100|}}\\ | ||
| + | |||
| + | |||
| + | |||
| + | ** User Group Base DN ** \\ | ||
| + | |||
| + | * When you click the button 'Pull User Group' after inserting the value, the user group information of AD server gets imported.\\ | ||
| + | |||
| + | Note: Initial value 'None' before you click the button \\ \\ | ||
| + | |||
| + | |||
| + | |||
| + | ** User Group ** \\ | ||
| - | The initial value is 'Inactive', which synchronizes all users.\\ \\ | + | * If 'User Group' is selected, 'Update' button gets activated.\\ |
| - | Once you toggle to 'Active', it synchronizes users according to the 'User Group Base DN' and 'User Group' setting. \\ | + | * The information is saved once you click 'Update'. If the user group information does not get updated at least once, an error will popup when user attempts to synchronize.\\ |
| - | {{:en:active_directory_02.png?nolink&1100|}}\\ | + | * If 'Pull User Group' is selected once again, the existing User Group settings get reset. \\ |
| - | ** User Group Base DN ** \\ | + | <callout type="primary" icon="warning"> |
| - | * When you click the button 'Pull User Group' after inserting value, the user group information of AD server is imported. (Initial value 'None' before the button click) \\ \\ | + | |
| - | ** User Group ** \\ | + | User Group information on AD is not displayed in BioStar. |
| - | * If 'User Group' is selected, 'Update' button is activated.\\ | + | |
| - | * The information is saved once you click 'Update'. If the user group information is not updated at least once, an error popup occurs when attempting to synchronize.\\ | + | |
| - | * If 'Pull User Group' is selected again, reset the existing User Group settings. \\ | + | |
| - | <callout type="primary" icon="warning"> | + | </callout> |
| - | User Group information on AD is not displayed in BioStar. | + | |
| - | </callout> | + | |